dmesg - PERC H700 - Intel Xeon L5609
registered as cooling_device4
processor LNXCPU:05: registered as cooling_device5
processor LNXCPU:06: registered as cooling_device6
processor LNXCPU:07: registered as cooling_device7
oczpcie 0000:05:00.0: oczpcie: driver version v4.0.551
alloc irq_desc for 35 on node -1
alloc kstat_irqs on node -1
alloc irq_2_iommu on node -1
oczpcie 0000:05:00.0: PCI INT A -> GSI 35 (level, low) -> IRQ 35
oczpcie 0000:05:00.0: setting latency timer to 64
ACPI: WMI: Mapper loaded
oczpcie 0000:05:00.0: oczpcie: PCI-E x4, Bandwidth Usage: 5.0 Gbps
Error: Driver 'pcspkr' is already registered, aborting...
usb-storage: device scan complete
usb-storage: device scan complete
scsi 3:0:0:0: Direct-Access iDRAC LCDRIVE 0323 PQ: 0 ANSI: 0 CCS
scsi 4:0:0:0: CD-ROM iDRAC Virtual CD 0323 PQ: 0 ANSI: 0
sd 3:0:0:0: Attached scsi generic sg4 type 0
scsi 4:0:0:1: Direct-Access iDRAC Virtual Floppy 0323 PQ: 0 ANSI: 0 CCS
sd 3:0:0:0: [sdc] Attached SCSI removable disk
sr1: scsi3-mmc drive: 0x/0x cd/rw caddy
sr 4:0:0:0: Attached scsi CD-ROM sr1
sr 4:0:0:0: Attached scsi generic sg5 type 5
sd 4:0:0:1: Attached scsi generic sg6 type 0
sd 4:0:0:1: [sdd] Attached SCSI removable disk
alloc irq_desc for 65 on node -1
alloc kstat_irqs on node -1
alloc irq_2_iommu on node -1
oczpcie 0000:05:00.0: irq 65 for MSI/MSI-X
oczpcie 0000:05:00.0: Model OCZ Z-DRIVE R4 CM88, firmware revision 2.15
oczpcie 0000:05:00.0: Device 0: Firmware does not support discard, discard will be disabled, please update your firmware
oczpcie 0000:05:00.0: Device 1: Firmware does not support discard, discard will be disabled, please update your firmware
oczpcie 0000:05:00.0: Device 2: Firmware does not support discard, discard will be disabled, please update your firmware
oczpcie 0000:05:00.0: Device 3: Firmware does not support discard, discard will be disabled, please update your firmware
oczpcie 0000:05:00.0: Device 4: Firmware does not support discard, discard will be disabled, please update your firmware
oczpcie 0000:05:00.0: Device 5: Firmware does not support discard, discard will be disabled, please update your firmware
oczpcie 0000:05:00.0: Device 6: Firmware does not support discard, discard will be disabled, please update your firmware
oczpcie 0000:05:00.0: Device 7: Firmware does not support discard, discard will be disabled, please update your firmware
oczvca: module license 'OCZ' taints kernel.
Disabling lock debugging due to kernel taint
oczpcie_5_0_ssd: oczpcie_5_0_ssd1
Adding 42084344k swap on /dev/sda5. Priority:-1 extents:1 across:42084344k
EXT3 FS on sda1, internal journal
kjournald starting. Commit interval 5 seconds
EXT3 FS on sda6, internal journal
EXT3-fs: mounted filesystem with ordered data mode.
EXT4-fs (dm-1): mounted filesystem with ordered data mode
EXT4-fs (dm-0): mounted filesystem with ordered data mode
Ethernet Channel Bonding Driver: v3.5.0 (November 4, 2008)
bonding: MII link monitoring set to 100 ms
ADDRCONF(NETDEV_UP): bond0: link is not ready
alloc irq_desc for 66 on node -1
alloc kstat_irqs on node -1
alloc irq_2_iommu on node -1
bnx2 0000:01:00.0: irq 66 for MSI/MSI-X
alloc irq_desc for 67 on node -1
alloc kstat_irqs on node -1
alloc irq_2_iommu on node -1
bnx2 0000:01:00.0: irq 67 for MSI/MSI-X
alloc irq_desc for 68 on node -1
alloc kstat_irqs on node -1
alloc irq_2_iommu on node -1
bnx2 0000:01:00.0: irq 68 for MSI/MSI-X
alloc irq_desc for 69 on node -1
alloc kstat_irqs on node -1
alloc irq_2_iommu on node -1
bnx2 0000:01:00.0: irq 69 for MSI/MSI-X
alloc irq_desc for 70 on node -1
alloc kstat_irqs on node -1
alloc irq_2_iommu on node -1
bnx2 0000:01:00.0: irq 70 for MSI/MSI-X
alloc irq_desc for 71 on node -1
alloc kstat_irqs on node -1
alloc irq_2_iommu on node -1
bnx2 0000:01:00.0: irq 71 for MSI/MSI-X
alloc irq_desc for 72 on node -1
alloc kstat_irqs on node -1
alloc irq_2_iommu on node -1
bnx2 0000:01:00.0: irq 72 for MSI/MSI-X
alloc irq_desc for 73 on node -1
alloc kstat_irqs on node -1
alloc irq_2_iommu on node -1
bnx2 0000:01:00.0: irq 73 for MSI/MSI-X
alloc irq_desc for 74 on node -1
alloc kstat_irqs on node -1
alloc irq_2_iommu on node -1
bnx2 0000:01:00.0: irq 74 for MSI/MSI-X
bnx2: eth0: using MSIX
bonding: bond0: enslaving eth0 as a backup interface with a down link.
alloc irq_desc for 75 on node -1
alloc kstat_irqs on node -1
alloc irq_2_iommu on node -1
bnx2 0000:01:00.1: irq 75 for MSI/MSI-X
alloc irq_desc for 76 on node -1
alloc kstat_irqs on node -1
alloc irq_2_iommu on node -1
bnx2 0000:01:00.1: irq 76 for MSI/MSI-X
alloc irq_desc for 77 on node -1
alloc kstat_irqs on node -1
alloc irq_2_iommu on node -1
bnx2 0000:01:00.1: irq 77 for MSI/MSI-X
alloc irq_desc for 78 on node -1
alloc kstat_irqs on node -1
alloc irq_2_iommu on node -1
bnx2 0000:01:00.1: irq 78 for MSI/MSI-X
alloc irq_desc for 79 on node -1
alloc kstat_irqs on node -1
alloc irq_2_iommu on node -1
bnx2 0000:01:00.1: irq 79 for MSI/MSI-X
alloc irq_desc for 80 on node -1
alloc kstat_irqs on node -1
alloc irq_2_iommu on node -1
bnx2 0000:01:00.1: irq 80 for MSI/MSI-X
alloc irq_desc for 81 on node -1
alloc kstat_irqs on node -1
alloc irq_2_iommu on node -1
bnx2 0000:01:00.1: irq 81 for MSI/MSI-X
alloc irq_desc for 82 on node -1
alloc kstat_irqs on node -1
alloc irq_2_iommu on node -1
bnx2 0000:01:00.1: irq 82 for MSI/MSI-X
alloc irq_desc for 83 on node -1
alloc kstat_irqs on node -1
alloc irq_2_iommu on node -1
bnx2 0000:01:00.1: irq 83 for MSI/MSI-X
bnx2: eth1: using MSIX
bonding: bond0: enslaving eth1 as a backup interface with a down link.
bnx2: eth0 NIC Copper Link is Up, 1000 Mbps full duplex, receive & transmit flow control ON
bonding: bond0: link status up for interface eth0, enabling it in 0 ms.
bonding: bond0: link status definitely up for interface eth0.
bonding: bond0: making interface eth0 the new active one.
bonding: bond0: first active interface up!
ADDRCONF(NETDEV_CHANGE): bond0: link becomes ready
bnx2: eth1 NIC Copper Link is Up, 1000 Mbps full duplex, receive & transmit flow control ON
bonding: bond0: link status up for interface eth1, enabling it in 200 ms.
bonding: bond0: link status definitely up for interface eth1.
ip_tables: (C) 2000-2006 Netfilter Core Team
nf_conntrack version 0.5.0 (16384 buckets, 65536 max)
CONFIG_NF_CT_ACCT is deprecated and will be removed soon. Please use
nf_conntrack.acct=1 kernel parameter, acct=1 nf_conntrack module option or
sysctl net.netfilter.nf_conntrack_acct=1 to enable it.
usb 3-1: USB disconnect, address 2
device eth0 entered promiscuous mode
device eth0 left promiscuous mode
device eth0 entered promiscuous mode
device eth0 left promiscuous mode
device eth0 entered promiscuous mode
device eth0 left promiscuous mode
usb 2-3: USB disconnect, address 3
usb 5-2: reset full speed USB device using uhci_hcd and address 2
usb 5-2: device descriptor read/64, error -71
usb 5-2: device descriptor read/64, error -71
usb 5-2: reset full speed USB device using uhci_hcd and address 2
usb 5-2: device descriptor read/64, error -71
usb 5-2: device descriptor read/64, error -71
usb 5-2: reset full speed USB device using uhci_hcd and address 2
usb 5-2: device not accepting address 2, error -71
usb 5-2: reset full speed USB device using uhci_hcd and address 2
usb 5-2: device not accepting address 2, error -71
usb 5-2: USB disconnect, address 2
usb 5-2: new full speed USB device using uhci_hcd and address 3
usb 5-2: device descriptor read/64, error -71
usb 5-2: device descriptor read/64, error -71
usb 5-2: new full speed USB device using uhci_hcd and address 4
usb 5-2: device descriptor read/64, error -71
usb 5-2: device descriptor read/64, error -71
usb 5-2: new full speed USB device using uhci_hcd and address 5
usb 5-2: device not accepting address 5, error -71
usb 5-2: new full speed USB device using uhci_hcd and address 6
usb 5-2: device not accepting address 6, error -71
hub 5-0:1.0: unable to enumerate USB device on port 2
usb 5-2: new full speed USB device using uhci_hcd and address 7
usb 5-2: New USB device found, idVendor=0624, idProduct=0248
usb 5-2: New USB device strings: Mfr=1, Product=2, SerialNumber=3
usb 5-2: Product: USB Composite Device-0
usb 5-2: Manufacturer: Avocent
usb 5-2: SerialNumber: 20120430
usb 5-2: configuration #1 chosen from 1 choice
input: Avocent USB Composite Device-0 as /devices/pci0000:00/0000:00:1d.0/usb5/5-2/5-2:1.0/input/input6
generic-usb 0003:0624:0248.0004: input,hidraw0: USB HID v1.00 Keyboard [Avocent USB Composite Device-0] on usb-0000:00:1d.0-2/input0
input: Avocent USB Composite Device-0 as /devices/pci0000:00/0000:00:1d.0/usb5/5-2/5-2:1.1/input/input7
generic-usb 0003:0624:0248.0005: input,hidraw1: USB HID v1.00 Mouse [Avocent USB Composite Device-0] on usb-0000:00:1d.0-2/input1
usb 2-3: new high speed USB device using ehci_hcd and address 4
usb 2-3: New USB device found, idVendor=0624, idProduct=0249
usb 2-3: New USB device strings: Mfr=1, Product=2, SerialNumber=3
usb 2-3: Product: USB Composite Device-1
usb 2-3: Manufacturer: Avocent
usb 2-3: SerialNumber: 20120430-1
usb 2-3: configuration #1 chosen from 1 choice
scsi5 : SCSI emulation for USB Mass Storage devices
usb-storage: device found at 4
usb-storage: waiting for device to settle before scanning
usb-storage: device scan complete
scsi 5:0:0:0: CD-ROM iDRAC Virtual CD 0323 PQ: 0 ANSI: 0
scsi 5:0:0:1: Direct-Access iDRAC Virtual Floppy 0323 PQ: 0 ANSI: 0 CCS
usb 2-3: USB disconnect, address 4
sr1: scsi3-mmc drive: 0x/0x cd/rw caddy
sr 5:0:0:0: Attached scsi CD-ROM sr1
sr 5:0:0:0: Attached scsi generic sg4 type 5
sd 5:0:0:1: Attached scsi generic sg5 type 0
sd 5:0:0:1: [sdc] READ CAPACITY failed
sd 5:0:0:1: [sdc] Result: hostbyte=DID_NO_CONNECT driverbyte=DRIVER_OK
sd 5:0:0:1: [sdc] Sense not available.
sd 5:0:0:1: [sdc] Write Protect is off
sd 5:0:0:1: [sdc] Mode Sense: 73 70 6c 75
sd 5:0:0:1: [sdc] Assuming drive cache: write through
sd 5:0:0:1: [sdc] READ CAPACITY failed
sd 5:0:0:1: [sdc] Result: hostbyte=DID_NO_CONNECT driverbyte=DRIVER_OK
sd 5:0:0:1: [sdc] Sense not available.
sd 5:0:0:1: [sdc] Assuming drive cache: write through
sd 5:0:0:1: [sdc] Attached SCSI removable disk
usb 2-3: new high speed USB device using ehci_hcd and address 5
usb 2-3: New USB device found, idVendor=0624, idProduct=0249
usb 2-3: New USB device strings: Mfr=1, Product=2, SerialNumber=3
usb 2-3: Product: USB Composite Device-1
usb 2-3: Manufacturer: Avocent
usb 2-3: SerialNumber: 20120430
usb 2-3: configuration #1 chosen from 1 choice
scsi6 : SCSI emulation for USB Mass Storage devices
usb-storage: device found at 5
usb-storage: waiting for device to settle before scanning
scsi7 : SCSI emulation for USB Mass Storage devices
usb-storage: device found at 5
usb-storage: waiting for device to settle before scanning
usb-storage: device scan complete
scsi 6:0:0:0: Direct-Access iDRAC LCDRIVE 0323 PQ: 0 ANSI: 0 CCS
sd 6:0:0:0: Attached scsi generic sg4 type 0
usb-storage: device scan complete
scsi 7:0:0:0: CD-ROM iDRAC Virtual CD 0323 PQ: 0 ANSI: 0
sd 6:0:0:0: [sdc] Attached SCSI removable disk
scsi 7:0:0:1: Direct-Access iDRAC Virtual Floppy 0323 PQ: 0 ANSI: 0 CCS
sr1: scsi3-mmc drive: 0x/0x cd/rw caddy
sr 7:0:0:0: Attached scsi CD-ROM sr1
sr 7:0:0:0: Attached scsi generic sg5 type 5
sd 7:0:0:1: Attached scsi generic sg6 type 0
sd 7:0:0:1: [sdd] Attached SCSI removable disk
usb 2-3: USB disconnect, address 5
usb 5-2: reset full speed USB device using uhci_hcd and address 7
usb 5-2: device descriptor read/64, error -71
usb 5-2: device descriptor read/64, error -71
usb 5-2: reset full speed USB device using uhci_hcd and address 7
usb 5-2: device descriptor read/64, error -71
usb 5-2: device descriptor read/64, error -71
usb 5-2: reset full speed USB device using uhci_hcd and address 7
usb 5-2: device not accepting address 7, error -71
usb 5-2: reset full speed USB device using uhci_hcd and address 7
usb 5-2: device not accepting address 7, error -71
usb 5-2: USB disconnect, address 7
usb 5-2: new full speed USB device using uhci_hcd and address 8
usb 5-2: device descriptor read/64, error -71
usb 5-2: device descriptor read/64, error -71
usb 5-2: new full speed USB device using uhci_hcd and address 9
usb 5-2: device descriptor read/64, error -71
usb 5-2: device descriptor read/64, error -71
usb 5-2: new full speed USB device using uhci_hcd and address 10
usb 5-2: device not accepting address 10, error -71
usb 5-2: new full speed USB device using uhci_hcd and address 11
usb 5-2: device not accepting address 11, error -71
hub 5-0:1.0: unable to enumerate USB device on port 2
usb 5-2: new full speed USB device using uhci_hcd and address 12
usb 5-2: New USB device found, idVendor=0624, idProduct=0248
usb 5-2: New USB device strings: Mfr=1, Product=2, SerialNumber=3
usb 5-2: Product: USB Composite Device-0
usb 5-2: Manufacturer: Avocent
usb 5-2: SerialNumber: 20120430
usb 5-2: configuration #1 chosen from 1 choice
input: Avocent USB Composite Device-0 as /devices/pci0000:00/0000:00:1d.0/usb5/5-2/5-2:1.0/input/input8
generic-usb 0003:0624:0248.0006: input,hidraw0: USB HID v1.00 Keyboard [Avocent USB Composite Device-0] on usb-0000:00:1d.0-2/input0
input: Avocent USB Composite Device-0 as /devices/pci0000:00/0000:00:1d.0/usb5/5-2/5-2:1.1/input/input9
generic-usb 0003:0624:0248.0007: input,hidraw1: USB HID v1.00 Mouse [Avocent USB Composite Device-0] on usb-0000:00:1d.0-2/input1
usb 2-3: new high speed USB device using ehci_hcd and address 6
usb 2-3: New USB device found, idVendor=0624, idProduct=0249
usb 2-3: New USB device strings: Mfr=1, Product=2, SerialNumber=3
usb 2-3: Product: USB Composite Device-1
usb 2-3: Manufacturer: Avocent
usb 2-3: SerialNumber: 20120430-1
usb 2-3: configuration #1 chosen from 1 choice
scsi8 : SCSI emulation for USB Mass Storage devices
usb-storage: device found at 6
usb-storage: waiting for device to settle before scanning
usb 2-3: USB disconnect, address 6
usb 2-3: new high speed USB device using ehci_hcd and address 7
usb 2-3: New USB device found, idVendor=0624, idProduct=0249
usb 2-3: New USB device strings: Mfr=1, Product=2, SerialNumber=3
usb 2-3: Product: USB Composite Device-1
usb 2-3: Manufacturer: Avocent
usb 2-3: SerialNumber: 20120430
usb 2-3: configuration #1 chosen from 1 choice
scsi9 : SCSI emulation for USB Mass Storage devices
usb-storage: device found at 7
usb-storage: waiting for device to settle before scanning
scsi10 : SCSI emulation for USB Mass Storage devices
usb-storage: device found at 7
usb-storage: waiting for device to settle before scanning
usb-storage: device scan complete
usb-storage: device scan complete
scsi 10:0:0:0: CD-ROM iDRAC Virtual CD 0323 PQ: 0 ANSI: 0
scsi 9:0:0:0: Direct-Access iDRAC LCDRIVE 0323 PQ: 0 ANSI: 0 CCS
scsi 10:0:0:1: Direct-Access iDRAC Virtual Floppy 0323 PQ: 0 ANSI: 0 CCS
sr1: scsi3-mmc drive: 0x/0x cd/rw caddy
sr 10:0:0:0: Attached scsi CD-ROM sr1
sr 10:0:0:0: Attached scsi generic sg4 type 5
sd 10:0:0:1: Attached scsi generic sg5 type 0
sd 9:0:0:0: Attached scsi generic sg6 type 0
sd 10:0:0:1: [sdc] Attached SCSI removable disk
sd 9:0:0:0: [sdd] Attached SCSI removable disk
EXT4-fs (oczpcie_5_0_ssd1): mounted filesystem with ordered data mode
usb 2-3: USB disconnect, address 7
usb 5-2: reset full speed USB device using uhci_hcd and address 12
usb 5-2: device descriptor read/64, error -71
usb 5-2: device descriptor read/64, error -71
usb 5-2: reset full speed USB device using uhci_hcd and address 12
usb 5-2: device descriptor read/64, error -71
usb 5-2: device descriptor read/64, error -71
usb 5-2: reset full speed USB device using uhci_hcd and address 12
usb 5-2: device not accepting address 12, error -71
usb 5-2: reset full speed USB device using uhci_hcd and address 12
usb 5-2: device not accepting address 12, error -71
usb 5-2: USB disconnect, address 12
usb 5-2: new full speed USB device using uhci_hcd and address 13
usb 5-2: device descriptor read/64, error -71
usb 5-2: device descriptor read/64, error -71
usb 5-2: new full speed USB device using uhci_hcd and address 14
usb 5-2: device descriptor read/64, error -71
usb 5-2: device descriptor read/64, error -71
usb 5-2: new full speed USB device using uhci_hcd and address 15
usb 5-2: device not accepting address 15, error -71
usb 5-2: new full speed USB device using uhci_hcd and address 16
usb 5-2: device not accepting address 16, error -71
hub 5-0:1.0: unable to enumerate USB device on port 2
usb 5-2: new full speed USB device using uhci_hcd and address 17
usb 5-2: New USB device found, idVendor=0624, idProduct=0248
usb 5-2: New USB device strings: Mfr=1, Product=2, SerialNumber=3
usb 5-2: Product: USB Composite Device-0
usb 5-2: Manufacturer: Avocent
usb 5-2: SerialNumber: 20120430
usb 5-2: configuration #1 chosen from 1 choice
input: Avocent USB Composite Device-0 as /devices/pci0000:00/0000:00:1d.0/usb5/5-2/5-2:1.0/input/input10
generic-usb 0003:0624:0248.0008: input,hidraw0: USB HID v1.00 Keyboard [Avocent USB Composite Device-0] on usb-0000:00:1d.0-2/input0
input: Avocent USB Composite Device-0 as /devices/pci0000:00/0000:00:1d.0/usb5/5-2/5-2:1.1/input/input11
generic-usb 0003:0624:0248.0009: input,hidraw1: USB HID v1.00 Mouse [Avocent USB Composite Device-0] on usb-0000:00:1d.0-2/input1
usb 2-3: new high speed USB device using ehci_hcd and address 8
usb 2-3: New USB device found, idVendor=0624, idProduct=0249
usb 2-3: New USB device strings: Mfr=1, Product=2, SerialNumber=3
usb 2-3: Product: USB Composite Device-1
usb 2-3: Manufacturer: Avocent
usb 2-3: SerialNumber: 20120430-1
usb 2-3: configuration #1 chosen from 1 choice
scsi11 : SCSI emulation for USB Mass Storage devices
usb-storage: device found at 8
usb-storage: waiting for device to settle before scanning
usb-storage: device scan complete
scsi 11:0:0:0: CD-ROM iDRAC Virtual CD 0323 PQ: 0 ANSI: 0
scsi 11:0:0:1: Direct-Access iDRAC Virtual Floppy 0323 PQ: 0 ANSI: 0 CCS
usb 2-3: USB disconnect, address 8
sr1: scsi3-mmc drive: 0x/0x cd/rw caddy
sr 11:0:0:0: Attached scsi CD-ROM sr1
sr 11:0:0:0: Attached scsi generic sg4 type 5
sd 11:0:0:1: Attached scsi generic sg5 type 0
sd 11:0:0:1: [sdc] READ CAPACITY failed
sd 11:0:0:1: [sdc] Result: hostbyte=DID_NO_CONNECT driverbyte=DRIVER_OK
sd 11:0:0:1: [sdc] Sense not available.
sd 11:0:0:1: [sdc] Write Protect is off
sd 11:0:0:1: [sdc] Mode Sense: 00 00 00 00
sd 11:0:0:1: [sdc] Assuming drive cache: write through
sd 11:0:0:1: [sdc] READ CAPACITY failed
sd 11:0:0:1: [sdc] Result: hostbyte=DID_NO_CONNECT driverbyte=DRIVER_OK
sd 11:0:0:1: [sdc] Sense not available.
sd 11:0:0:1: [sdc] Assuming drive cache: write through
sd 11:0:0:1: [sdc] Attached SCSI removable disk
usb 2-3: new high speed USB device using ehci_hcd and address 9
usb 2-3: New USB device found, idVendor=0624, idProduct=0249
usb 2-3: New USB device strings: Mfr=1, Product=2, SerialNumber=3
usb 2-3: Product: USB Composite Device-1
usb 2-3: Manufacturer: Avocent
usb 2-3: SerialNumber: 20120430
usb 2-3: configuration #1 chosen from 1 choice
scsi12 : SCSI emulation for USB Mass Storage devices
usb-storage: device found at 9
usb-storage: waiting for device to settle before scanning
scsi13 : SCSI emulation for USB Mass Storage devices
usb-storage: device found at 9
usb-storage: waiting for device to settle before scanning
usb-storage: device scan complete
usb-storage: device scan complete
scsi 13:0:0:0: CD-ROM iDRAC Virtual CD 0323 PQ: 0 ANSI: 0
scsi 12:0:0:0: Direct-Access iDRAC LCDRIVE 0323 PQ: 0 ANSI: 0 CCS
scsi 13:0:0:1: Direct-Access iDRAC Virtual Floppy 0323 PQ: 0 ANSI: 0 CCS
sd 12:0:0:0: Attached scsi generic sg4 type 0
sd 12:0:0:0: [sdc] Attached SCSI removable disk
sr1: scsi3-mmc drive: 0x/0x cd/rw caddy
sr 13:0:0:0: Attached scsi CD-ROM sr1
sr 13:0:0:0: Attached scsi generic sg5 type 5
sd 13:0:0:1: Attached scsi generic sg6 type 0
sd 13:0:0:1: [sdd] Attached SCSI removable disk
usb 2-3: USB disconnect, address 9
usb 5-2: reset full speed USB device using uhci_hcd and address 17
usb 5-2: device descriptor read/64, error -71
usb 5-2: device descriptor read/64, error -71
usb 5-2: reset full speed USB device using uhci_hcd and address 17
usb 5-2: device descriptor read/64, error -71
usb 5-2: device descriptor read/64, error -71
usb 5-2: reset full speed USB device using uhci_hcd and address 17
usb 5-2: device not accepting address 17, error -71
usb 5-2: reset full speed USB device using uhci_hcd and address 17
usb 5-2: device not accepting address 17, error -71
usb 5-2: USB disconnect, address 17
usb 5-2: new full speed USB device using uhci_hcd and address 18
usb 5-2: device descriptor read/64, error -71
usb 5-2: device descriptor read/64, error -71
usb 5-2: new full speed USB device using uhci_hcd and address 19
usb 5-2: device descriptor read/64, error -71
usb 5-2: device descriptor read/64, error -71
usb 5-2: new full speed USB device using uhci_hcd and address 20
usb 5-2: device not accepting address 20, error -71
usb 5-2: new full speed USB device using uhci_hcd and address 21
usb 5-2: device not accepting address 21, error -71
hub 5-0:1.0: unable to enumerate USB device on port 2
usb 5-2: new full speed USB device using uhci_hcd and address 22
usb 5-2: New USB device found, idVendor=0624, idProduct=0248
usb 5-2: New USB device strings: Mfr=1, Product=2, SerialNumber=3
usb 5-2: Product: USB Composite Device-0
usb 5-2: Manufacturer: Avocent
usb 5-2: SerialNumber: 20120430
usb 5-2: configuration #1 chosen from 1 choice
input: Avocent USB Composite Device-0 as /devices/pci0000:00/0000:00:1d.0/usb5/5-2/5-2:1.0/input/input12
generic-usb 0003:0624:0248.000A: input,hidraw0: USB HID v1.00 Keyboard [Avocent USB Composite Device-0] on usb-0000:00:1d.0-2/input0
input: Avocent USB Composite Device-0 as /devices/pci0000:00/0000:00:1d.0/usb5/5-2/5-2:1.1/input/input13
generic-usb 0003:0624:0248.000B: input,hidraw1: USB HID v1.00 Mouse [Avocent USB Composite Device-0] on usb-0000:00:1d.0-2/input1
usb 2-3: new high speed USB device using ehci_hcd and address 10
usb 2-3: New USB device found, idVendor=0624, idProduct=0249
usb 2-3: New USB device strings: Mfr=1, Product=2, SerialNumber=3
usb 2-3: Product: USB Composite Device-1
usb 2-3: Manufacturer: Avocent
usb 2-3: SerialNumber: 20120430-1
usb 2-3: configuration #1 chosen from 1 choice
scsi14 : SCSI emulation for USB Mass Storage devices
usb-storage: device found at 10
usb-storage: waiting for device to settle before scanning
usb-storage: device scan complete
scsi 14:0:0:0: CD-ROM iDRAC Virtual CD 0323 PQ: 0 ANSI: 0
scsi 14:0:0:1: Direct-Access iDRAC Virtual Floppy 0323 PQ: 0 ANSI: 0 CCS
usb 2-3: USB disconnect, address 10
sr1: scsi3-mmc drive: 0x/0x cd/rw caddy
sr 14:0:0:0: Attached scsi CD-ROM sr1
sr 14:0:0:0: Attached scsi generic sg4 type 5
sd 14:0:0:1: Attached scsi generic sg5 type 0
sd 14:0:0:1: [sdc] READ CAPACITY failed
sd 14:0:0:1: [sdc] Result: hostbyte=DID_NO_CONNECT driverbyte=DRIVER_OK
sd 14:0:0:1: [sdc] Sense not available.
sd 14:0:0:1: [sdc] Write Protect is off
sd 14:0:0:1: [sdc] Mode Sense: 00 00 00 00
sd 14:0:0:1: [sdc] Assuming drive cache: write through
sd 14:0:0:1: [sdc] READ CAPACITY failed
sd 14:0:0:1: [sdc] Result: hostbyte=DID_NO_CONNECT driverbyte=DRIVER_OK
sd 14:0:0:1: [sdc] Sense not available.
sd 14:0:0:1: [sdc] Assuming drive cache: write through
sd 14:0:0:1: [sdc] Attached SCSI removable disk
usb 2-3: new high speed USB device using ehci_hcd and address 11
usb 2-3: New USB device found, idVendor=0624, idProduct=0249
usb 2-3: New USB device strings: Mfr=1, Product=2, SerialNumber=3
usb 2-3: Product: USB Composite Device-1
usb 2-3: Manufacturer: Avocent
usb 2-3: SerialNumber: 20120430
usb 2-3: configuration #1 chosen from 1 choice
scsi15 : SCSI emulation for USB Mass Storage devices
usb-storage: device found at 11
usb-storage: waiting for device to settle before scanning
scsi16 : SCSI emulation for USB Mass Storage devices
usb-storage: device found at 11
usb-storage: waiting for device to settle before scanning
usb-storage: device scan complete
usb-storage: device scan complete
scsi 15:0:0:0: Direct-Access iDRAC LCDRIVE 0323 PQ: 0 ANSI: 0 CCS
scsi 16:0:0:0: CD-ROM iDRAC Virtual CD 0323 PQ: 0 ANSI: 0
scsi 16:0:0:1: Direct-Access iDRAC Virtual Floppy 0323 PQ: 0 ANSI: 0 CCS
sr1: scsi3-mmc drive: 0x/0x cd/rw caddy
sr 16:0:0:0: Attached scsi CD-ROM sr1
sr 16:0:0:0: Attached scsi generic sg4 type 5
sd 16:0:0:1: Attached scsi generic sg5 type 0
sd 15:0:0:0: Attached scsi generic sg6 type 0
sd 15:0:0:0: [sdd] Attached SCSI removable disk
sd 16:0:0:1: [sdc] Attached SCSI removable disk
usb 2-3: USB disconnect, address 11
usb 5-2: reset full speed USB device using uhci_hcd and address 22
usb 5-2: device descriptor read/64, error -71
usb 5-2: device descriptor read/64, error -71
usb 5-2: reset full speed USB device using uhci_hcd and address 22
usb 5-2: device descriptor read/64, error -71
usb 5-2: device descriptor read/64, error -71
usb 5-2: reset full speed USB device using uhci_hcd and address 22
usb 5-2: device not accepting address 22, error -71
usb 5-2: reset full speed USB device using uhci_hcd and address 22
usb 5-2: device not accepting address 22, error -71
usb 5-2: USB disconnect, address 22
usb 5-2: new full speed USB device using uhci_hcd and address 23
usb 5-2: device descriptor read/64, error -71
usb 5-2: device descriptor read/64, error -71
usb 5-2: new full speed USB device using uhci_hcd and address 24
usb 5-2: device descriptor read/64, error -71
usb 5-2: device descriptor read/64, error -71
usb 5-2: new full speed USB device using uhci_hcd and address 25
usb 5-2: device not accepting address 25, error -71
usb 5-2: new full speed USB device using uhci_hcd and address 26
usb 5-2: device not accepting address 26, error -71
hub 5-0:1.0: unable to enumerate USB device on port 2
usb 5-2: new full speed USB device using uhci_hcd and address 27
usb 5-2: New USB device found, idVendor=0624, idProduct=0248
usb 5-2: New USB device strings: Mfr=1, Product=2, SerialNumber=3
usb 5-2: Product: USB Composite Device-0
usb 5-2: Manufacturer: Avocent
usb 5-2: SerialNumber: 20120430
usb 5-2: configuration #1 chosen from 1 choice
input: Avocent USB Composite Device-0 as /devices/pci0000:00/0000:00:1d.0/usb5/5-2/5-2:1.0/input/input14
generic-usb 0003:0624:0248.000C: input,hidraw0: USB HID v1.00 Keyboard [Avocent USB Composite Device-0] on usb-0000:00:1d.0-2/input0
input: Avocent USB Composite Device-0 as /devices/pci0000:00/0000:00:1d.0/usb5/5-2/5-2:1.1/input/input15
generic-usb 0003:0624:0248.000D: input,hidraw1: USB HID v1.00 Mouse [Avocent USB Composite Device-0] on usb-0000:00:1d.0-2/input1
usb 2-3: new high speed USB device using ehci_hcd and address 12
usb 2-3: New USB device found, idVendor=0624, idProduct=0249
usb 2-3: New USB device strings: Mfr=1, Product=2, SerialNumber=3
usb 2-3: Product: USB Composite Device-1
usb 2-3: Manufacturer: Avocent
usb 2-3: SerialNumber: 20120430-1
usb 2-3: configuration #1 chosen from 1 choice
scsi17 : SCSI emulation for USB Mass Storage devices
usb-storage: device found at 12
usb-storage: waiting for device to settle before scanning
usb 2-3: USB disconnect, address 12
usb 2-3: new high speed USB device using ehci_hcd and address 13
usb 2-3: New USB device found, idVendor=0624, idProduct=0249
usb 2-3: New USB device strings: Mfr=1, Product=2, SerialNumber=3
usb 2-3: Product: USB Composite Device-1
usb 2-3: Manufacturer: Avocent
usb 2-3: SerialNumber: 20120430
usb 2-3: configuration #1 chosen from 1 choice
scsi18 : SCSI emulation for USB Mass Storage devices
usb-storage: device found at 13
usb-storage: waiting for device to settle before scanning
scsi19 : SCSI emulation for USB Mass Storage devices
usb-storage: device found at 13
usb-storage: waiting for device to settle before scanning
usb-storage: device scan complete
usb-storage: device scan complete
scsi 19:0:0:0: CD-ROM iDRAC Virtual CD 0323 PQ: 0 ANSI: 0
scsi 18:0:0:0: Direct-Access iDRAC LCDRIVE 0323 PQ: 0 ANSI: 0 CCS
scsi 19:0:0:1: Direct-Access iDRAC Virtual Floppy 0323 PQ: 0 ANSI: 0 CCS
sd 18:0:0:0: Attached scsi generic sg4 type 0
sd 18:0:0:0: [sdc] Attached SCSI removable disk
sr1: scsi3-mmc drive: 0x/0x cd/rw caddy
sr 19:0:0:0: Attached scsi CD-ROM sr1
sr 19:0:0:0: Attached scsi generic sg5 type 5
sd 19:0:0:1: Attached scsi generic sg6 type 0
sd 19:0:0:1: [sdd] Attached SCSI removable disk
usb 2-3: USB disconnect, address 13
usb 5-2: reset full speed USB device using uhci_hcd and address 27
usb 5-2: device descriptor read/64, error -71
usb 5-2: device descriptor read/64, error -71
usb 5-2: reset full speed USB device using uhci_hcd and address 27
usb 5-2: device descriptor read/64, error -71
usb 5-2: device descriptor read/64, error -71
usb 5-2: reset full speed USB device using uhci_hcd and address 27
usb 5-2: device not accepting address 27, error -71
usb 5-2: reset full speed USB device using uhci_hcd and address 27
usb 5-2: device not accepting address 27, error -71
usb 5-2: USB disconnect, address 27
usb 5-2: new full speed USB device using uhci_hcd and address 28
usb 5-2: device descriptor read/64, error -71
usb 5-2: device descriptor read/64, error -71
usb 5-2: new full speed USB device using uhci_hcd and address 29
usb 5-2: device descriptor read/64, error -71
usb 5-2: device descriptor read/64, error -71
usb 5-2: new full speed USB device using uhci_hcd and address 30
usb 5-2: device not accepting address 30, error -71
usb 5-2: new full speed USB device using uhci_hcd and address 31
usb 5-2: device not accepting address 31, error -71
hub 5-0:1.0: unable to enumerate USB device on port 2
usb 5-2: new full speed USB device using uhci_hcd and address 32
usb 5-2: New USB device found, idVendor=0624, idProduct=0248
usb 5-2: New USB device strings: Mfr=1, Product=2, SerialNumber=3
usb 5-2: Product: USB Composite Device-0
usb 5-2: Manufacturer: Avocent
usb 5-2: SerialNumber: 20120430
usb 5-2: configuration #1 chosen from 1 choice
input: Avocent USB Composite Device-0 as /devices/pci0000:00/0000:00:1d.0/usb5/5-2/5-2:1.0/input/input16
generic-usb 0003:0624:0248.000E: input,hidraw0: USB HID v1.00 Keyboard [Avocent USB Composite Device-0] on usb-0000:00:1d.0-2/input0
input: Avocent USB Composite Device-0 as /devices/pci0000:00/0000:00:1d.0/usb5/5-2/5-2:1.1/input/input17
generic-usb 0003:0624:0248.000F: input,hidraw1: USB HID v1.00 Mouse [Avocent USB Composite Device-0] on usb-0000:00:1d.0-2/input1
usb 2-3: new high speed USB device using ehci_hcd and address 14
usb 2-3: New USB device found, idVendor=0624, idProduct=0249
usb 2-3: New USB device strings: Mfr=1, Product=2, SerialNumber=3
usb 2-3: Product: USB Composite Device-1
usb 2-3: Manufacturer: Avocent
usb 2-3: SerialNumber: 20120430-1
usb 2-3: configuration #1 chosen from 1 choice
scsi20 : SCSI emulation for USB Mass Storage devices
usb-storage: device found at 14
usb-storage: waiting for device to settle before scanning
usb-storage: device scan complete
scsi 20:0:0:0: CD-ROM iDRAC Virtual CD 0323 PQ: 0 ANSI: 0
scsi 20:0:0:1: Direct-Access iDRAC Virtual Floppy 0323 PQ: 0 ANSI: 0 CCS
sr1: scsi3-mmc drive: 0x/0x cd/rw caddy
sr 20:0:0:0: Attached scsi CD-ROM sr1
sr 20:0:0:0: Attached scsi generic sg4 type 5
sd 20:0:0:1: Attached scsi generic sg5 type 0
sd 20:0:0:1: [sdc] Attached SCSI removable disk
usb 2-3: USB disconnect, address 14
usb 2-3: new high speed USB device using ehci_hcd and address 15
usb 2-3: New USB device found, idVendor=0624, idProduct=0249
usb 2-3: New USB device strings: Mfr=1, Product=2, SerialNumber=3
usb 2-3: Product: USB Composite Device-1
usb 2-3: Manufacturer: Avocent
usb 2-3: SerialNumber: 20120430
usb 2-3: configuration #1 chosen from 1 choice
scsi21 : SCSI emulation for USB Mass Storage devices
usb-storage: device found at 15
usb-storage: waiting for device to settle before scanning
scsi22 : SCSI emulation for USB Mass Storage devices
usb-storage: device found at 15
usb-storage: waiting for device to settle before scanning
usb-storage: device scan complete
usb-storage: device scan complete
scsi 21:0:0:0: Direct-Access iDRAC LCDRIVE 0323 PQ: 0 ANSI: 0 CCS
scsi 22:0:0:0: CD-ROM iDRAC Virtual CD 0323 PQ: 0 ANSI: 0
scsi 22:0:0:1: Direct-Access iDRAC Virtual Floppy 0323 PQ: 0 ANSI: 0 CCS
sr1: scsi3-mmc drive: 0x/0x cd/rw caddy
sr 22:0:0:0: Attached scsi CD-ROM sr1
sr 22:0:0:0: Attached scsi generic sg4 type 5
sd 22:0:0:1: Attached scsi generic sg5 type 0
sd 21:0:0:0: Attached scsi generic sg6 type 0
sd 21:0:0:0: [sdd] Attached SCSI removable disk
sd 22:0:0:1: [sdc] Attached SCSI removable disk
usb 2-3: USB disconnect, address 15
usb 5-2: reset full speed USB device using uhci_hcd and address 32
usb 5-2: device descriptor read/64, error -71
usb 5-2: device descriptor read/64, error -71
usb 5-2: reset full speed USB device using uhci_hcd and address 32
usb 5-2: device descriptor read/64, error -71
usb 5-2: device descriptor read/64, error -71
usb 5-2: reset full speed USB device using uhci_hcd and address 32
usb 5-2: device not accepting address 32, error -71
usb 5-2: reset full speed USB device using uhci_hcd and address 32
usb 5-2: device not accepting address 32, error -71
usb 5-2: USB disconnect, address 32
usb 5-2: new full speed USB device using uhci_hcd and address 33
usb 5-2: device descriptor read/64, error -71
usb 5-2: device descriptor read/64, error -71
usb 5-2: new full speed USB device using uhci_hcd and address 34
usb 5-2: device descriptor read/64, error -71
usb 5-2: device descriptor read/64, error -71
usb 5-2: new full speed USB device using uhci_hcd and address 35
usb 5-2: device not accepting address 35, error -71
usb 5-2: new full speed USB device using uhci_hcd and address 36
usb 5-2: device not accepting address 36, error -71
hub 5-0:1.0: unable to enumerate USB device on port 2
usb 5-2: new full speed USB device using uhci_hcd and address 37
usb 5-2: New USB device found, idVendor=0624, idProduct=0248
usb 5-2: New USB device strings: Mfr=1, Product=2, SerialNumber=3
usb 5-2: Product: USB Composite Device-0
usb 5-2: Manufacturer: Avocent
usb 5-2: SerialNumber: 20120430
usb 5-2: configuration #1 chosen from 1 choice
input: Avocent USB Composite Device-0 as /devices/pci0000:00/0000:00:1d.0/usb5/5-2/5-2:1.0/input/input18
generic-usb 0003:0624:0248.0010: input,hidraw0: USB HID v1.00 Keyboard [Avocent USB Composite Device-0] on usb-0000:00:1d.0-2/input0
input: Avocent USB Composite Device-0 as /devices/pci0000:00/0000:00:1d.0/usb5/5-2/5-2:1.1/input/input19
generic-usb 0003:0624:0248.0011: input,hidraw1: USB HID v1.00 Mouse [Avocent USB Composite Device-0] on usb-0000:00:1d.0-2/input1
usb 2-3: new high speed USB device using ehci_hcd and address 16
usb 2-3: New USB device found, idVendor=0624, idProduct=0249
usb 2-3: New USB device strings: Mfr=1, Product=2, SerialNumber=3
usb 2-3: Product: USB Composite Device-1
usb 2-3: Manufacturer: Avocent
usb 2-3: SerialNumber: 20120430-1
usb 2-3: configuration #1 chosen from 1 choice
scsi23 : SCSI emulation for USB Mass Storage devices
usb-storage: device found at 16
usb-storage: waiting for device to settle before scanning
usb 2-3: USB disconnect, address 16
usb 2-3: new high speed USB device using ehci_hcd and address 17
usb 2-3: New USB device found, idVendor=0624, idProduct=0249
usb 2-3: New USB device strings: Mfr=1, Product=2, SerialNumber=3
usb 2-3: Product: USB Composite Device-1
usb 2-3: Manufacturer: Avocent
usb 2-3: SerialNumber: 20120430
usb 2-3: configuration #1 chosen from 1 choice
scsi24 : SCSI emulation for USB Mass Storage devices
usb-storage: device found at 17
usb-storage: waiting for device to settle before scanning
scsi25 : SCSI emulation for USB Mass Storage devices
usb-storage: device found at 17
usb-storage: waiting for device to settle before scanning
usb-storage: device scan complete
usb-storage: device scan complete
scsi 25:0:0:0: CD-ROM iDRAC Virtual CD 0323 PQ: 0 ANSI: 0
scsi 24:0:0:0: Direct-Access iDRAC LCDRIVE 0323 PQ: 0 ANSI: 0 CCS
scsi 25:0:0:1: Direct-Access iDRAC Virtual Floppy 0323 PQ: 0 ANSI: 0 CCS
sd 24:0:0:0: Attached scsi generic sg4 type 0
sd 24:0:0:0: [sdc] Attached SCSI removable disk
sr1: scsi3-mmc drive: 0x/0x cd/rw caddy
sr 25:0:0:0: Attached scsi CD-ROM sr1
sr 25:0:0:0: Attached scsi generic sg5 type 5
sd 25:0:0:1: Attached scsi generic sg6 type 0
sd 25:0:0:1: [sdd] Attached SCSI removable disk
usb 2-3: USB disconnect, address 17
usb 5-2: reset full speed USB device using uhci_hcd and address 37
usb 5-2: device descriptor read/64, error -71
usb 5-2: device descriptor read/64, error -71
usb 5-2: reset full speed USB device using uhci_hcd and address 37
usb 5-2: device descriptor read/64, error -71
usb 5-2: device descriptor read/64, error -71
usb 5-2: reset full speed USB device using uhci_hcd and address 37
usb 5-2: device not accepting address 37, error -71
usb 5-2: reset full speed USB device using uhci_hcd and address 37
usb 5-2: device not accepting address 37, error -71
usb 5-2: USB disconnect, address 37
usb 5-2: new full speed USB device using uhci_hcd and address 38
usb 5-2: device descriptor read/64, error -71
usb 5-2: device descriptor read/64, error -71
usb 5-2: new full speed USB device using uhci_hcd and address 39
usb 5-2: device descriptor read/64, error -71
usb 5-2: device descriptor read/64, error -71
usb 5-2: new full speed USB device using uhci_hcd and address 40
usb 5-2: device not accepting address 40, error -71
usb 5-2: new full speed USB device using uhci_hcd and address 41
usb 5-2: device not accepting address 41, error -71
hub 5-0:1.0: unable to enumerate USB device on port 2
usb 5-2: new full speed USB device using uhci_hcd and address 42
usb 5-2: New USB device found, idVendor=0624, idProduct=0248
usb 5-2: New USB device strings: Mfr=1, Product=2, SerialNumber=3
usb 5-2: Product: USB Composite Device-0
usb 5-2: Manufacturer: Avocent
usb 5-2: SerialNumber: 20120430
usb 5-2: configuration #1 chosen from 1 choice
input: Avocent USB Composite Device-0 as /devices/pci0000:00/0000:00:1d.0/usb5/5-2/5-2:1.0/input/input20
generic-usb 0003:0624:0248.0012: input,hidraw0: USB HID v1.00 Keyboard [Avocent USB Composite Device-0] on usb-0000:00:1d.0-2/input0
input: Avocent USB Composite Device-0 as /devices/pci0000:00/0000:00:1d.0/usb5/5-2/5-2:1.1/input/input21
generic-usb 0003:0624:0248.0013: input,hidraw1: USB HID v1.00 Mouse [Avocent USB Composite Device-0] on usb-0000:00:1d.0-2/input1
usb 2-3: new high speed USB device using ehci_hcd and address 18
usb 2-3: New USB device found, idVendor=0624, idProduct=0249
usb 2-3: New USB device strings: Mfr=1, Product=2, SerialNumber=3
usb 2-3: Product: USB Composite Device-1
usb 2-3: Manufacturer: Avocent
usb 2-3: SerialNumber: 20120430-1
usb 2-3: configuration #1 chosen from 1 choice
scsi26 : SCSI emulation for USB Mass Storage devices
usb-storage: device found at 18
usb-storage: waiting for device to settle before scanning
usb 2-3: USB disconnect, address 18
usb 2-3: new high speed USB device using ehci_hcd and address 19
usb 2-3: New USB device found, idVendor=0624, idProduct=0249
usb 2-3: New USB device strings: Mfr=1, Product=2, SerialNumber=3
usb 2-3: Product: USB Composite Device-1
usb 2-3: Manufacturer: Avocent
usb 2-3: SerialNumber: 20120430
usb 2-3: configuration #1 chosen from 1 choice
scsi27 : SCSI emulation for USB Mass Storage devices
usb-storage: device found at 19
usb-storage: waiting for device to settle before scanning
scsi28 : SCSI emulation for USB Mass Storage devices
usb-storage: device found at 19
usb-storage: waiting for device to settle before scanning
usb-storage: device scan complete
usb-storage: device scan complete
scsi 27:0:0:0: Direct-Access iDRAC LCDRIVE 0323 PQ: 0 ANSI: 0 CCS
scsi 28:0:0:0: CD-ROM iDRAC Virtual CD 0323 PQ: 0 ANSI: 0
sd 27:0:0:0: Attached scsi generic sg4 type 0
scsi 28:0:0:1: Direct-Access iDRAC Virtual Floppy 0323 PQ: 0 ANSI: 0 CCS
sd 27:0:0:0: [sdc] Attached SCSI removable disk
sr1: scsi3-mmc drive: 0x/0x cd/rw caddy
sr 28:0:0:0: Attached scsi CD-ROM sr1
sr 28:0:0:0: Attached scsi generic sg5 type 5
sd 28:0:0:1: Attached scsi generic sg6 type 0
sd 28:0:0:1: [sdd] Attached SCSI removable disk
usb 2-3: USB disconnect, address 19
usb 5-2: reset full speed USB device using uhci_hcd and address 42
usb 5-2: device descriptor read/64, error -71
usb 5-2: device descriptor read/64, error -71
usb 5-2: reset full speed USB device using uhci_hcd and address 42
usb 5-2: device descriptor read/64, error -71
usb 5-2: device descriptor read/64, error -71
usb 5-2: reset full speed USB device using uhci_hcd and address 42
usb 5-2: device not accepting address 42, error -71
usb 5-2: reset full speed USB device using uhci_hcd and address 42
usb 5-2: device not accepting address 42, error -71
usb 5-2: USB disconnect, address 42
usb 5-2: new full speed USB device using uhci_hcd and address 43
usb 5-2: device descriptor read/64, error -71
usb 5-2: device descriptor read/64, error -71
usb 5-2: new full speed USB device using uhci_hcd and address 44
usb 5-2: device descriptor read/64, error -71
usb 5-2: device descriptor read/64, error -71
usb 5-2: new full speed USB device using uhci_hcd and address 45
usb 5-2: device not accepting address 45, error -71
usb 5-2: new full speed USB device using uhci_hcd and address 46
usb 5-2: device not accepting address 46, error -71
hub 5-0:1.0: unable to enumerate USB device on port 2
usb 5-2: new full speed USB device using uhci_hcd and address 47
usb 5-2: New USB device found, idVendor=0624, idProduct=0248
usb 5-2: New USB device strings: Mfr=1, Product=2, SerialNumber=3
usb 5-2: Product: USB Composite Device-0
usb 5-2: Manufacturer: Avocent
usb 5-2: SerialNumber: 20120430
usb 5-2: configuration #1 chosen from 1 choice
input: Avocent USB Composite Device-0 as /devices/pci0000:00/0000:00:1d.0/usb5/5-2/5-2:1.0/input/input22
generic-usb 0003:0624:0248.0014: input,hidraw0: USB HID v1.00 Keyboard [Avocent USB Composite Device-0] on usb-0000:00:1d.0-2/input0
input: Avocent USB Composite Device-0 as /devices/pci0000:00/0000:00:1d.0/usb5/5-2/5-2:1.1/input/input23
generic-usb 0003:0624:0248.0015: input,hidraw1: USB HID v1.00 Mouse [Avocent USB Composite Device-0] on usb-0000:00:1d.0-2/input1
usb 2-3: new high speed USB device using ehci_hcd and address 20
usb 2-3: New USB device found, idVendor=0624, idProduct=0249
usb 2-3: New USB device strings: Mfr=1, Product=2, SerialNumber=3
usb 2-3: Product: USB Composite Device-1
usb 2-3: Manufacturer: Avocent
usb 2-3: SerialNumber: 20120430-1
usb 2-3: configuration #1 chosen from 1 choice
scsi29 : SCSI emulation for USB Mass Storage devices
usb-storage: device found at 20
usb-storage: waiting for device to settle before scanning
usb 2-3: USB disconnect, address 20
usb 2-3: new high speed USB device using ehci_hcd and address 21
usb 2-3: New USB device found, idVendor=0624, idProduct=0249
usb 2-3: New USB device strings: Mfr=1, Product=2, SerialNumber=3
usb 2-3: Product: USB Composite Device-1
usb 2-3: Manufacturer: Avocent
usb 2-3: SerialNumber: 20120430
usb 2-3: configuration #1 chosen from 1 choice
scsi30 : SCSI emulation for USB Mass Storage devices
usb-storage: device found at 21
usb-storage: waiting for device to settle before scanning
scsi31 : SCSI emulation for USB Mass Storage devices
usb-storage: device found at 21
usb-storage: waiting for device to settle before scanning
usb-storage: device scan complete
usb-storage: device scan complete
scsi 31:0:0:0: CD-ROM iDRAC Virtual CD 0323 PQ: 0 ANSI: 0
scsi 30:0:0:0: Direct-Access iDRAC LCDRIVE 0323 PQ: 0 ANSI: 0 CCS
scsi 31:0:0:1: Direct-Access iDRAC Virtual Floppy 0323 PQ: 0 ANSI: 0 CCS
sd 30:0:0:0: Attached scsi generic sg4 type 0
sd 30:0:0:0: [sdc] Attached SCSI removable disk
sr1: scsi3-mmc drive: 0x/0x cd/rw caddy
sr 31:0:0:0: Attached scsi CD-ROM sr1
sr 31:0:0:0: Attached scsi generic sg5 type 5
sd 31:0:0:1: Attached scsi generic sg6 type 0
sd 31:0:0:1: [sdd] Attached SCSI removable disk
usb 2-3: USB disconnect, address 21
usb 5-2: reset full speed USB device using uhci_hcd and address 47
usb 5-2: device descriptor read/64, error -71
usb 5-2: device descriptor read/64, error -71
usb 5-2: reset full speed USB device using uhci_hcd and address 47
usb 5-2: device descriptor read/64, error -71
usb 5-2: device descriptor read/64, error -71
usb 5-2: reset full speed USB device using uhci_hcd and address 47
usb 5-2: device not accepting address 47, error -71
usb 5-2: reset full speed USB device using uhci_hcd and address 47
usb 5-2: device not accepting address 47, error -71
usb 5-2: USB disconnect, address 47
usb 5-2: new full speed USB device using uhci_hcd and address 48
usb 5-2: device descriptor read/64, error -71
usb 5-2: device descriptor read/64, error -71
usb 5-2: new full speed USB device using uhci_hcd and address 49
usb 5-2: device descriptor read/64, error -71
usb 5-2: device descriptor read/64, error -71
usb 5-2: new full speed USB device using uhci_hcd and address 50
usb 5-2: device not accepting address 50, error -71
usb 5-2: new full speed USB device using uhci_hcd and address 51
usb 5-2: device not accepting address 51, error -71
hub 5-0:1.0: unable to enumerate USB device on port 2
usb 5-2: new full speed USB device using uhci_hcd and address 52
usb 5-2: New USB device found, idVendor=0624, idProduct=0248
usb 5-2: New USB device strings: Mfr=1, Product=2, SerialNumber=3
usb 5-2: Product: USB Composite Device-0
usb 5-2: Manufacturer: Avocent
usb 5-2: SerialNumber: 20120430
usb 5-2: configuration #1 chosen from 1 choice
input: Avocent USB Composite Device-0 as /devices/pci0000:00/0000:00:1d.0/usb5/5-2/5-2:1.0/input/input24
generic-usb 0003:0624:0248.0016: input,hidraw0: USB HID v1.00 Keyboard [Avocent USB Composite Device-0] on usb-0000:00:1d.0-2/input0
input: Avocent USB Composite Device-0 as /devices/pci0000:00/0000:00:1d.0/usb5/5-2/5-2:1.1/input/input25
generic-usb 0003:0624:0248.0017: input,hidraw1: USB HID v1.00 Mouse [Avocent USB Composite Device-0] on usb-0000:00:1d.0-2/input1
usb 2-3: new high speed USB device using ehci_hcd and address 22
usb 2-3: New USB device found, idVendor=0624, idProduct=0249
usb 2-3: New USB device strings: Mfr=1, Product=2, SerialNumber=3
usb 2-3: Product: USB Composite Device-1
usb 2-3: Manufacturer: Avocent
usb 2-3: SerialNumber: 20120430-1
usb 2-3: configuration #1 chosen from 1 choice
scsi32 : SCSI emulation for USB Mass Storage devices
usb-storage: device found at 22
usb-storage: waiting for device to settle before scanning
usb-storage: device scan complete
scsi 32:0:0:0: CD-ROM iDRAC Virtual CD 0323 PQ: 0 ANSI: 0
scsi 32:0:0:1: Direct-Access iDRAC Virtual Floppy 0323 PQ: 0 ANSI: 0 CCS
usb 2-3: USB disconnect, address 22
sr1: scsi3-mmc drive: 0x/0x cd/rw caddy
sr 32:0:0:0: Attached scsi CD-ROM sr1
sr 32:0:0:0: Attached scsi generic sg4 type 5
sd 32:0:0:1: Attached scsi generic sg5 type 0
sd 32:0:0:1: [sdc] READ CAPACITY failed
sd 32:0:0:1: [sdc] Result: hostbyte=DID_NO_CONNECT driverbyte=DRIVER_OK
sd 32:0:0:1: [sdc] Sense not available.
sd 32:0:0:1: [sdc] Write Protect is on
sd 32:0:0:1: [sdc] Mode Sense: ff ff ff ff
sd 32:0:0:1: [sdc] Assuming drive cache: write through
sd 32:0:0:1: [sdc] READ CAPACITY failed
sd 32:0:0:1: [sdc] Result: hostbyte=DID_NO_CONNECT driverbyte=DRIVER_OK
sd 32:0:0:1: [sdc] Sense not available.
sd 32:0:0:1: [sdc] Assuming drive cache: write through
sd 32:0:0:1: [sdc] Attached SCSI removable disk
usb 2-3: new high speed USB device using ehci_hcd and address 23
usb 2-3: New USB device found, idVendor=0624, idProduct=0249
usb 2-3: New USB device strings: Mfr=1, Product=2, SerialNumber=3
usb 2-3: Product: USB Composite Device-1
usb 2-3: Manufacturer: Avocent
usb 2-3: SerialNumber: 20120430
usb 2-3: configuration #1 chosen from 1 choice
scsi33 : SCSI emulation for USB Mass Storage devices
usb-storage: device found at 23
usb-storage: waiting for device to settle before scanning
scsi34 : SCSI emulation for USB Mass Storage devices
usb-storage: device found at 23
usb-storage: waiting for device to settle before scanning
usb-storage: device scan complete
usb-storage: device scan complete
scsi 34:0:0:0: CD-ROM iDRAC Virtual CD 0323 PQ: 0 ANSI: 0
scsi 33:0:0:0: Direct-Access iDRAC LCDRIVE 0323 PQ: 0 ANSI: 0 CCS
scsi 34:0:0:1: Direct-Access iDRAC Virtual Floppy 0323 PQ: 0 ANSI: 0 CCS
sd 33:0:0:0: Attached scsi generic sg4 type 0
sd 33:0:0:0: [sdc] Attached SCSI removable disk
sr1: scsi3-mmc drive: 0x/0x cd/rw caddy
sr 34:0:0:0: Attached scsi CD-ROM sr1
sr 34:0:0:0: Attached scsi generic sg5 type 5
sd 34:0:0:1: Attached scsi generic sg6 type 0
sd 34:0:0:1: [sdd] Attached SCSI removable disk
process `sysctl' is using deprecated sysctl (syscall) net.ipv6.neigh.default.retrans_time; Use net.ipv6.neigh.default.retrans_time_ms instead.
usb 2-3: USB disconnect, address 23
usb 5-2: reset full speed USB device using uhci_hcd and address 52
usb 5-2: device descriptor read/64, error -71
usb 5-2: device descriptor read/64, error -71
usb 5-2: reset full speed USB device using uhci_hcd and address 52
usb 5-2: device descriptor read/64, error -71
usb 5-2: device descriptor read/64, error -71
usb 5-2: reset full speed USB device using uhci_hcd and address 52
usb 5-2: device not accepting address 52, error -71
usb 5-2: reset full speed USB device using uhci_hcd and address 52
usb 5-2: device not accepting address 52, error -71
usb 5-2: USB disconnect, address 52
usb 5-2: new full speed USB device using uhci_hcd and address 53
usb 5-2: device descriptor read/64, error -71
usb 5-2: device descriptor read/64, error -71
usb 5-2: new full speed USB device using uhci_hcd and address 54
usb 5-2: device descriptor read/64, error -71
usb 5-2: device descriptor read/64, error -71
usb 5-2: new full speed USB device using uhci_hcd and address 55
usb 5-2: device not accepting address 55, error -71
usb 5-2: new full speed USB device using uhci_hcd and address 56
usb 5-2: device not accepting address 56, error -71
hub 5-0:1.0: unable to enumerate USB device on port 2
usb 5-2: new full speed USB device using uhci_hcd and address 57
usb 5-2: New USB device found, idVendor=0624, idProduct=0248
usb 5-2: New USB device strings: Mfr=1, Product=2, SerialNumber=3
usb 5-2: Product: USB Composite Device-0
usb 5-2: Manufacturer: Avocent
usb 5-2: SerialNumber: 20120430
usb 5-2: configuration #1 chosen from 1 choice
input: Avocent USB Composite Device-0 as /devices/pci0000:00/0000:00:1d.0/usb5/5-2/5-2:1.0/input/input26
generic-usb 0003:0624:0248.0018: input,hidraw0: USB HID v1.00 Keyboard [Avocent USB Composite Device-0] on usb-0000:00:1d.0-2/input0
input: Avocent USB Composite Device-0 as /devices/pci0000:00/0000:00:1d.0/usb5/5-2/5-2:1.1/input/input27
generic-usb 0003:0624:0248.0019: input,hidraw1: USB HID v1.00 Mouse [Avocent USB Composite Device-0] on usb-0000:00:1d.0-2/input1
usb 2-3: new high speed USB device using ehci_hcd and address 24
usb 2-3: New USB device found, idVendor=0624, idProduct=0249
usb 2-3: New USB device strings: Mfr=1, Product=2, SerialNumber=3
usb 2-3: Product: USB Composite Device-1
usb 2-3: Manufacturer: Avocent
usb 2-3: SerialNumber: 20120430-1
usb 2-3: configuration #1 chosen from 1 choice
scsi35 : SCSI emulation for USB Mass Storage devices
usb-storage: device found at 24
usb-storage: waiting for device to settle before scanning
usb 2-3: USB disconnect, address 24
usb 2-3: new high speed USB device using ehci_hcd and address 25
usb 2-3: New USB device found, idVendor=0624, idProduct=0249
usb 2-3: New USB device strings: Mfr=1, Product=2, SerialNumber=3
usb 2-3: Product: USB Composite Device-1
usb 2-3: Manufacturer: Avocent
usb 2-3: SerialNumber: 20120430
usb 2-3: configuration #1 chosen from 1 choice
scsi36 : SCSI emulation for USB Mass Storage devices
usb-storage: device found at 25
usb-storage: waiting for device to settle before scanning
scsi37 : SCSI emulation for USB Mass Storage devices
usb-storage: device found at 25
usb-storage: waiting for device to settle before scanning
usb-storage: device scan complete
usb-storage: device scan complete
scsi 36:0:0:0: Direct-Access iDRAC LCDRIVE 0323 PQ: 0 ANSI: 0 CCS
scsi 37:0:0:0: CD-ROM iDRAC Virtual CD 0323 PQ: 0 ANSI: 0
scsi 37:0:0:1: Direct-Access iDRAC Virtual Floppy 0323 PQ: 0 ANSI: 0 CCS
sd 36:0:0:0: Attached scsi generic sg4 type 0
sd 36:0:0:0: [sdc] Attached SCSI removable disk
sr1: scsi3-mmc drive: 0x/0x cd/rw caddy
sr 37:0:0:0: Attached scsi CD-ROM sr1
sr 37:0:0:0: Attached scsi generic sg5 type 5
sd 37:0:0:1: Attached scsi generic sg6 type 0
sd 37:0:0:1: [sdd] Attached SCSI removable disk
bonding: bond0: Warning: the permanent HWaddr of eth0 - b8:ac:6f:8e:22:fc - is still in use by bond0. Set the HWaddr of eth0 to a different address to avoid conflicts.
bonding: bond0: releasing active interface eth0
bonding: bond0: making interface eth1 the new active one.
bonding: bond0: releasing active interface eth1
Ethernet Channel Bonding Driver: v3.5.0 (November 4, 2008)
bonding: MII link monitoring set to 100 ms
ADDRCONF(NETDEV_UP): bond0: link is not ready
bnx2 0000:01:00.0: irq 66 for MSI/MSI-X
bnx2 0000:01:00.0: irq 67 for MSI/MSI-X
bnx2 0000:01:00.0: irq 68 for MSI/MSI-X
bnx2 0000:01:00.0: irq 69 for MSI/MSI-X
bnx2 0000:01:00.0: irq 70 for MSI/MSI-X
bnx2 0000:01:00.0: irq 71 for MSI/MSI-X
bnx2 0000:01:00.0: irq 72 for MSI/MSI-X
bnx2 0000:01:00.0: irq 73 for MSI/MSI-X
bnx2 0000:01:00.0: irq 74 for MSI/MSI-X
bnx2: eth0: using MSIX
bonding: bond0: enslaving eth0 as a backup interface with a down link.
bnx2 0000:01:00.1: irq 75 for MSI/MSI-X
bnx2 0000:01:00.1: irq 76 for MSI/MSI-X
bnx2 0000:01:00.1: irq 77 for MSI/MSI-X
bnx2 0000:01:00.1: irq 78 for MSI/MSI-X
bnx2 0000:01:00.1: irq 79 for MSI/MSI-X
bnx2 0000:01:00.1: irq 80 for MSI/MSI-X
bnx2 0000:01:00.1: irq 81 for MSI/MSI-X
bnx2 0000:01:00.1: irq 82 for MSI/MSI-X
bnx2 0000:01:00.1: irq 83 for MSI/MSI-X
bnx2: eth1: using MSIX
bonding: bond0: enslaving eth1 as a backup interface with a down link.
bnx2: eth0 NIC Copper Link is Up, 1000 Mbps full duplex, receive & transmit flow control ON
bonding: bond0: link status up for interface eth0, enabling it in 0 ms.
bonding: bond0: link status definitely up for interface eth0.
bonding: bond0: making interface eth0 the new active one.
bonding: bond0: first active interface up!
ADDRCONF(NETDEV_CHANGE): bond0: link becomes ready
bnx2: eth1 NIC Copper Link is Up, 1000 Mbps full duplex, receive & transmit flow control ON
bonding: bond0: link status up for interface eth1, enabling it in 200 ms.
bonding: bond0: link status definitely up for interface eth1.
usb 2-3: USB disconnect, address 25
usb 5-2: reset full speed USB device using uhci_hcd and address 57
usb 5-2: device descriptor read/64, error -71
usb 5-2: device descriptor read/64, error -71
usb 5-2: reset full speed USB device using uhci_hcd and address 57
usb 5-2: device descriptor read/64, error -71
usb 5-2: device descriptor read/64, error -71
usb 5-2: reset full speed USB device using uhci_hcd and address 57
usb 5-2: device not accepting address 57, error -71
usb 5-2: reset full speed USB device using uhci_hcd and address 57
usb 5-2: device not accepting address 57, error -71
usb 5-2: USB disconnect, address 57
usb 5-2: new full speed USB device using uhci_hcd and address 58
usb 5-2: device descriptor read/64, error -71
usb 5-2: device descriptor read/64, error -71
usb 5-2: new full speed USB device using uhci_hcd and address 59
usb 5-2: device descriptor read/64, error -71
usb 5-2: device descriptor read/64, error -71
usb 5-2: new full speed USB device using uhci_hcd and address 60
usb 5-2: device not accepting address 60, error -71
usb 5-2: new full speed USB device using uhci_hcd and address 61
usb 5-2: device not accepting address 61, error -71
hub 5-0:1.0: unable to enumerate USB device on port 2
usb 5-2: new full speed USB device using uhci_hcd and address 62
usb 5-2: New USB device found, idVendor=0624, idProduct=0248
usb 5-2: New USB device strings: Mfr=1, Product=2, SerialNumber=3
usb 5-2: Product: USB Composite Device-0
usb 5-2: Manufacturer: Avocent
usb 5-2: SerialNumber: 20120430
usb 5-2: configuration #1 chosen from 1 choice
input: Avocent USB Composite Device-0 as /devices/pci0000:00/0000:00:1d.0/usb5/5-2/5-2:1.0/input/input28
generic-usb 0003:0624:0248.001A: input,hidraw0: USB HID v1.00 Keyboard [Avocent USB Composite Device-0] on usb-0000:00:1d.0-2/input0
input: Avocent USB Composite Device-0 as /devices/pci0000:00/0000:00:1d.0/usb5/5-2/5-2:1.1/input/input29
generic-usb 0003:0624:0248.001B: input,hidraw1: USB HID v1.00 Mouse [Avocent USB Composite Device-0] on usb-0000:00:1d.0-2/input1
usb 2-3: new high speed USB device using ehci_hcd and address 26
usb 2-3: New USB device found, idVendor=0624, idProduct=0249
usb 2-3: New USB device strings: Mfr=1, Product=2, SerialNumber=3
usb 2-3: Product: USB Composite Device-1
usb 2-3: Manufacturer: Avocent
usb 2-3: SerialNumber: 20120430-1
usb 2-3: configuration #1 chosen from 1 choice
scsi38 : SCSI emulation for USB Mass Storage devices
usb-storage: device found at 26
usb-storage: waiting for device to settle before scanning
usb 2-3: USB disconnect, address 26
usb 2-3: new high speed USB device using ehci_hcd and address 27
usb 2-3: New USB device found, idVendor=0624, idProduct=0249
usb 2-3: New USB device strings: Mfr=1, Product=2, SerialNumber=3
usb 2-3: Product: USB Composite Device-1
usb 2-3: Manufacturer: Avocent
usb 2-3: SerialNumber: 20120430
usb 2-3: configuration #1 chosen from 1 choice
scsi39 : SCSI emulation for USB Mass Storage devices
usb-storage: device found at 27
usb-storage: waiting for device to settle before scanning
scsi40 : SCSI emulation for USB Mass Storage devices
usb-storage: device found at 27
usb-storage: waiting for device to settle before scanning
usb-storage: device scan complete
usb-storage: device scan complete
scsi 39:0:0:0: Direct-Access iDRAC LCDRIVE 0323 PQ: 0 ANSI: 0 CCS
scsi 40:0:0:0: CD-ROM iDRAC Virtual CD 0323 PQ: 0 ANSI: 0
sd 39:0:0:0: Attached scsi generic sg4 type 0
scsi 40:0:0:1: Direct-Access iDRAC Virtual Floppy 0323 PQ: 0 ANSI: 0 CCS
sd 39:0:0:0: [sdc] Attached SCSI removable disk
sr1: scsi3-mmc drive: 0x/0x cd/rw caddy
sr 40:0:0:0: Attached scsi CD-ROM sr1
sr 40:0:0:0: Attached scsi generic sg5 type 5
sd 40:0:0:1: Attached scsi generic sg6 type 0
sd 40:0:0:1: [sdd] Attached SCSI removable disk
usb 2-3: USB disconnect, address 27
usb 5-2: reset full speed USB device using uhci_hcd and address 62
usb 5-2: device descriptor read/64, error -71
usb 5-2: device descriptor read/64, error -71
usb 5-2: reset full speed USB device using uhci_hcd and address 62
usb 5-2: device descriptor read/64, error -71
usb 5-2: device descriptor read/64, error -71
usb 5-2: reset full speed USB device using uhci_hcd and address 62
usb 5-2: device not accepting address 62, error -71
usb 5-2: reset full speed USB device using uhci_hcd and address 62
usb 5-2: device not accepting address 62, error -71
usb 5-2: USB disconnect, address 62
usb 5-2: new full speed USB device using uhci_hcd and address 63
usb 5-2: device descriptor read/64, error -71
usb 5-2: device descriptor read/64, error -71
usb 5-2: new full speed USB device using uhci_hcd and address 64
usb 5-2: device descriptor read/64, error -71
usb 5-2: device descriptor read/64, error -71
usb 5-2: new full speed USB device using uhci_hcd and address 65
usb 5-2: device not accepting address 65, error -71
usb 5-2: new full speed USB device using uhci_hcd and address 66
usb 5-2: device not accepting address 66, error -71
hub 5-0:1.0: unable to enumerate USB device on port 2
usb 5-2: new full speed USB device using uhci_hcd and address 67
usb 5-2: New USB device found, idVendor=0624, idProduct=0248
usb 5-2: New USB device strings: Mfr=1, Product=2, SerialNumber=3
usb 5-2: Product: USB Composite Device-0
usb 5-2: Manufacturer: Avocent
usb 5-2: SerialNumber: 20120430
usb 5-2: configuration #1 chosen from 1 choice
input: Avocent USB Composite Device-0 as /devices/pci0000:00/0000:00:1d.0/usb5/5-2/5-2:1.0/input/input30
generic-usb 0003:0624:0248.001C: input,hidraw0: USB HID v1.00 Keyboard [Avocent USB Composite Device-0] on usb-0000:00:1d.0-2/input0
input: Avocent USB Composite Device-0 as /devices/pci0000:00/0000:00:1d.0/usb5/5-2/5-2:1.1/input/input31
generic-usb 0003:0624:0248.001D: input,hidraw1: USB HID v1.00 Mouse [Avocent USB Composite Device-0] on usb-0000:00:1d.0-2/input1
usb 2-3: new high speed USB device using ehci_hcd and address 28
usb 2-3: New USB device found, idVendor=0624, idProduct=0249
usb 2-3: New USB device strings: Mfr=1, Product=2, SerialNumber=3
usb 2-3: Product: USB Composite Device-1
usb 2-3: Manufacturer: Avocent
usb 2-3: SerialNumber: 20120430-1
usb 2-3: configuration #1 chosen from 1 choice
scsi41 : SCSI emulation for USB Mass Storage devices
usb-storage: device found at 28
usb-storage: waiting for device to settle before scanning
usb 2-3: USB disconnect, address 28
usb 2-3: new high speed USB device using ehci_hcd and address 29
usb 2-3: New USB device found, idVendor=0624, idProduct=0249
usb 2-3: New USB device strings: Mfr=1, Product=2, SerialNumber=3
usb 2-3: Product: USB Composite Device-1
usb 2-3: Manufacturer: Avocent
usb 2-3: SerialNumber: 20120430
usb 2-3: configuration #1 chosen from 1 choice
scsi42 : SCSI emulation for USB Mass Storage devices
usb-storage: device found at 29
usb-storage: waiting for device to settle before scanning
scsi43 : SCSI emulation for USB Mass Storage devices
usb-storage: device found at 29
usb-storage: waiting for device to settle before scanning
usb-storage: device scan complete
usb-storage: device scan complete
scsi 43:0:0:0: CD-ROM iDRAC Virtual CD 0323 PQ: 0 ANSI: 0
scsi 42:0:0:0: Direct-Access iDRAC LCDRIVE 0323 PQ: 0 ANSI: 0 CCS
scsi 43:0:0:1: Direct-Access iDRAC Virtual Floppy 0323 PQ: 0 ANSI: 0 CCS
sd 42:0:0:0: Attached scsi generic sg4 type 0
sd 42:0:0:0: [sdc] Attached SCSI removable disk
sr1: scsi3-mmc drive: 0x/0x cd/rw caddy
sr 43:0:0:0: Attached scsi CD-ROM sr1
sr 43:0:0:0: Attached scsi generic sg5 type 5
sd 43:0:0:1: Attached scsi generic sg6 type 0
sd 43:0:0:1: [sdd] Attached SCSI removable disk
usb 2-3: USB disconnect, address 29
usb 5-2: reset full speed USB device using uhci_hcd and address 67
usb 5-2: device descriptor read/64, error -71
usb 5-2: device descriptor read/64, error -71
usb 5-2: reset full speed USB device using uhci_hcd and address 67
usb 5-2: device descriptor read/64, error -71
usb 5-2: device descriptor read/64, error -71
usb 5-2: reset full speed USB device using uhci_hcd and address 67
usb 5-2: device not accepting address 67, error -71
usb 5-2: reset full speed USB device using uhci_hcd and address 67
usb 5-2: device not accepting address 67, error -71
usb 5-2: USB disconnect, address 67
usb 5-2: new full speed USB device using uhci_hcd and address 68
usb 5-2: device descriptor read/64, error -71
usb 5-2: device descriptor read/64, error -71
usb 5-2: new full speed USB device using uhci_hcd and address 69
usb 5-2: device descriptor read/64, error -71
usb 5-2: device descriptor read/64, error -71
usb 5-2: new full speed USB device using uhci_hcd and address 70
usb 5-2: device not accepting address 70, error -71
usb 5-2: new full speed USB device using uhci_hcd and address 71
usb 5-2: device not accepting address 71, error -71
hub 5-0:1.0: unable to enumerate USB device on port 2
usb 5-2: new full speed USB device using uhci_hcd and address 72
usb 5-2: New USB device found, idVendor=0624, idProduct=0248
usb 5-2: New USB device strings: Mfr=1, Product=2, SerialNumber=3
usb 5-2: Product: USB Composite Device-0
usb 5-2: Manufacturer: Avocent
usb 5-2: SerialNumber: 20120430
usb 5-2: configuration #1 chosen from 1 choice
input: Avocent USB Composite Device-0 as /devices/pci0000:00/0000:00:1d.0/usb5/5-2/5-2:1.0/input/input32
generic-usb 0003:0624:0248.001E: input,hidraw0: USB HID v1.00 Keyboard [Avocent USB Composite Device-0] on usb-0000:00:1d.0-2/input0
input: Avocent USB Composite Device-0 as /devices/pci0000:00/0000:00:1d.0/usb5/5-2/5-2:1.1/input/input33
generic-usb 0003:0624:0248.001F: input,hidraw1: USB HID v1.00 Mouse [Avocent USB Composite Device-0] on usb-0000:00:1d.0-2/input1
usb 2-3: new high speed USB device using ehci_hcd and address 30
usb 2-3: New USB device found, idVendor=0624, idProduct=0249
usb 2-3: New USB device strings: Mfr=1, Product=2, SerialNumber=3
usb 2-3: Product: USB Composite Device-1
usb 2-3: Manufacturer: Avocent
usb 2-3: SerialNumber: 20120430-1
usb 2-3: configuration #1 chosen from 1 choice
scsi44 : SCSI emulation for USB Mass Storage devices
usb-storage: device found at 30
usb-storage: waiting for device to settle before scanning
usb-storage: device scan complete
scsi 44:0:0:0: CD-ROM iDRAC Virtual CD 0323 PQ: 0 ANSI: 0
scsi 44:0:0:1: Direct-Access iDRAC Virtual Floppy 0323 PQ: 0 ANSI: 0 CCS
usb 2-3: USB disconnect, address 30
sr1: scsi3-mmc drive: 0x/0x cd/rw caddy
sr 44:0:0:0: Attached scsi CD-ROM sr1
sr 44:0:0:0: Attached scsi generic sg4 type 5
sd 44:0:0:1: Attached scsi generic sg5 type 0
sd 44:0:0:1: [sdc] READ CAPACITY failed
sd 44:0:0:1: [sdc] Result: hostbyte=DID_NO_CONNECT driverbyte=DRIVER_OK
sd 44:0:0:1: [sdc] Sense not available.
sd 44:0:0:1: [sdc] Write Protect is off
sd 44:0:0:1: [sdc] Mode Sense: 00 00 00 00
sd 44:0:0:1: [sdc] Assuming drive cache: write through
sd 44:0:0:1: [sdc] READ CAPACITY failed
sd 44:0:0:1: [sdc] Result: hostbyte=DID_NO_CONNECT driverbyte=DRIVER_OK
sd 44:0:0:1: [sdc] Sense not available.
sd 44:0:0:1: [sdc] Assuming drive cache: write through
sd 44:0:0:1: [sdc] Attached SCSI removable disk
usb 2-3: new high speed USB device using ehci_hcd and address 31
usb 2-3: New USB device found, idVendor=0624, idProduct=0249
usb 2-3: New USB device strings: Mfr=1, Product=2, SerialNumber=3
usb 2-3: Product: USB Composite Device-1
usb 2-3: Manufacturer: Avocent
usb 2-3: SerialNumber: 20120430
usb 2-3: configuration #1 chosen from 1 choice
scsi45 : SCSI emulation for USB Mass Storage devices
usb-storage: device found at 31
usb-storage: waiting for device to settle before scanning
scsi46 : SCSI emulation for USB Mass Storage devices
usb-storage: device found at 31
usb-storage: waiting for device to settle before scanning
usb-storage: device scan complete
usb-storage: device scan complete
scsi 46:0:0:0: CD-ROM iDRAC Virtual CD 0323 PQ: 0 ANSI: 0
scsi 45:0:0:0: Direct-Access iDRAC LCDRIVE 0323 PQ: 0 ANSI: 0 CCS
sd 45:0:0:0: Attached scsi generic sg4 type 0
scsi 46:0:0:1: Direct-Access iDRAC Virtual Floppy 0323 PQ: 0 ANSI: 0 CCS
sd 45:0:0:0: [sdc] Attached SCSI removable disk
sr1: scsi3-mmc drive: 0x/0x cd/rw caddy
sr 46:0:0:0: Attached scsi CD-ROM sr1
sr 46:0:0:0: Attached scsi generic sg5 type 5
sd 46:0:0:1: Attached scsi generic sg6 type 0
sd 46:0:0:1: [sdd] Attached SCSI removable disk
usb 2-3: USB disconnect, address 31
usb 5-2: reset full speed USB device using uhci_hcd and address 72
usb 5-2: device descriptor read/64, error -71
usb 5-2: device descriptor read/64, error -71
usb 5-2: reset full speed USB device using uhci_hcd and address 72
usb 5-2: device descriptor read/64, error -71
usb 5-2: device descriptor read/64, error -71
usb 5-2: reset full speed USB device using uhci_hcd and address 72
usb 5-2: device not accepting address 72, error -71
usb 5-2: reset full speed USB device using uhci_hcd and address 72
usb 5-2: device not accepting address 72, error -71
usb 5-2: USB disconnect, address 72
usb 5-2: new full speed USB device using uhci_hcd and address 73
usb 5-2: device descriptor read/64, error -71
usb 5-2: device descriptor read/64, error -71
usb 5-2: new full speed USB device using uhci_hcd and address 74
usb 5-2: device descriptor read/64, error -71
usb 5-2: device descriptor read/64, error -71
usb 5-2: new full speed USB device using uhci_hcd and address 75
usb 5-2: device not accepting address 75, error -71
usb 5-2: new full speed USB device using uhci_hcd and address 76
usb 5-2: device not accepting address 76, error -71
hub 5-0:1.0: unable to enumerate USB device on port 2
usb 5-2: new full speed USB device using uhci_hcd and address 77
usb 5-2: New USB device found, idVendor=0624, idProduct=0248
usb 5-2: New USB device strings: Mfr=1, Product=2, SerialNumber=3
usb 5-2: Product: USB Composite Device-0
usb 5-2: Manufacturer: Avocent
usb 5-2: SerialNumber: 20120430
usb 5-2: configuration #1 chosen from 1 choice
input: Avocent USB Composite Device-0 as /devices/pci0000:00/0000:00:1d.0/usb5/5-2/5-2:1.0/input/input34
generic-usb 0003:0624:0248.0020: input,hidraw0: USB HID v1.00 Keyboard [Avocent USB Composite Device-0] on usb-0000:00:1d.0-2/input0
input: Avocent USB Composite Device-0 as /devices/pci0000:00/0000:00:1d.0/usb5/5-2/5-2:1.1/input/input35
generic-usb 0003:0624:0248.0021: input,hidraw1: USB HID v1.00 Mouse [Avocent USB Composite Device-0] on usb-0000:00:1d.0-2/input1
usb 2-3: new high speed USB device using ehci_hcd and address 32
usb 2-3: New USB device found, idVendor=0624, idProduct=0249
usb 2-3: New USB device strings: Mfr=1, Product=2, SerialNumber=3
usb 2-3: Product: USB Composite Device-1
usb 2-3: Manufacturer: Avocent
usb 2-3: SerialNumber: 20120430-1
usb 2-3: configuration #1 chosen from 1 choice
scsi47 : SCSI emulation for USB Mass Storage devices
usb-storage: device found at 32
usb-storage: waiting for device to settle before scanning
usb 2-3: USB disconnect, address 32
usb 2-3: new high speed USB device using ehci_hcd and address 33
usb 2-3: New USB device found, idVendor=0624, idProduct=0249
usb 2-3: New USB device strings: Mfr=1, Product=2, SerialNumber=3
usb 2-3: Product: USB Composite Device-1
usb 2-3: Manufacturer: Avocent
usb 2-3: SerialNumber: 20120430
usb 2-3: configuration #1 chosen from 1 choice
scsi48 : SCSI emulation for USB Mass Storage devices
usb-storage: device found at 33
usb-storage: waiting for device to settle before scanning
scsi49 : SCSI emulation for USB Mass Storage devices
usb-storage: device found at 33
usb-storage: waiting for device to settle before scanning
usb-storage: device scan complete
usb-storage: device scan complete
scsi 48:0:0:0: Direct-Access iDRAC LCDRIVE 0323 PQ: 0 ANSI: 0 CCS
scsi 49:0:0:0: CD-ROM iDRAC Virtual CD 0323 PQ: 0 ANSI: 0
scsi 49:0:0:1: Direct-Access iDRAC Virtual Floppy 0323 PQ: 0 ANSI: 0 CCS
sd 48:0:0:0: Attached scsi generic sg4 type 0
sd 48:0:0:0: [sdc] Attached SCSI removable disk
sr1: scsi3-mmc drive: 0x/0x cd/rw caddy
sr 49:0:0:0: Attached scsi CD-ROM sr1
sr 49:0:0:0: Attached scsi generic sg5 type 5
sd 49:0:0:1: Attached scsi generic sg6 type 0
sd 49:0:0:1: [sdd] Attached SCSI removable disk
usb 2-3: USB disconnect, address 33
usb 5-2: reset full speed USB device using uhci_hcd and address 77
usb 5-2: device descriptor read/64, error -71
usb 5-2: device descriptor read/64, error -71
usb 5-2: reset full speed USB device using uhci_hcd and address 77
usb 5-2: device descriptor read/64, error -71
usb 5-2: device descriptor read/64, error -71
usb 5-2: reset full speed USB device using uhci_hcd and address 77
usb 5-2: device not accepting address 77, error -71
usb 5-2: reset full speed USB device using uhci_hcd and address 77
usb 5-2: device not accepting address 77, error -71
usb 5-2: USB disconnect, address 77
usb 5-2: new full speed USB device using uhci_hcd and address 78
usb 5-2: device descriptor read/64, error -71
usb 5-2: device descriptor read/64, error -71
usb 5-2: new full speed USB device using uhci_hcd and address 79
usb 5-2: device descriptor read/64, error -71
usb 5-2: device descriptor read/64, error -71
usb 5-2: new full speed USB device using uhci_hcd and address 80
usb 5-2: device not accepting address 80, error -71
usb 5-2: new full speed USB device using uhci_hcd and address 81
usb 5-2: device not accepting address 81, error -71
hub 5-0:1.0: unable to enumerate USB device on port 2
usb 5-2: new full speed USB device using uhci_hcd and address 82
usb 5-2: New USB device found, idVendor=0624, idProduct=0248
usb 5-2: New USB device strings: Mfr=1, Product=2, SerialNumber=3
usb 5-2: Product: USB Composite Device-0
usb 5-2: Manufacturer: Avocent
usb 5-2: SerialNumber: 20120430
usb 5-2: configuration #1 chosen from 1 choice
input: Avocent USB Composite Device-0 as /devices/pci0000:00/0000:00:1d.0/usb5/5-2/5-2:1.0/input/input36
generic-usb 0003:0624:0248.0022: input,hidraw0: USB HID v1.00 Keyboard [Avocent USB Composite Device-0] on usb-0000:00:1d.0-2/input0
input: Avocent USB Composite Device-0 as /devices/pci0000:00/0000:00:1d.0/usb5/5-2/5-2:1.1/input/input37
generic-usb 0003:0624:0248.0023: input,hidraw1: USB HID v1.00 Mouse [Avocent USB Composite Device-0] on usb-0000:00:1d.0-2/input1
usb 2-3: new high speed USB device using ehci_hcd and address 34
usb 2-3: New USB device found, idVendor=0624, idProduct=0249
usb 2-3: New USB device strings: Mfr=1, Product=2, SerialNumber=3
usb 2-3: Product: USB Composite Device-1
usb 2-3: Manufacturer: Avocent
usb 2-3: SerialNumber: 20120430-1
usb 2-3: configuration #1 chosen from 1 choice
scsi50 : SCSI emulation for USB Mass Storage devices
usb-storage: device found at 34
usb-storage: waiting for device to settle before scanning
usb-storage: device scan complete
scsi 50:0:0:0: CD-ROM iDRAC Virtual CD 0323 PQ: 0 ANSI: 0
scsi 50:0:0:1: Direct-Access iDRAC Virtual Floppy 0323 PQ: 0 ANSI: 0 CCS
usb 2-3: USB disconnect, address 34
sr1: scsi3-mmc drive: 0x/0x cd/rw caddy
sr 50:0:0:0: Attached scsi CD-ROM sr1
sr 50:0:0:0: Attached scsi generic sg4 type 5
sd 50:0:0:1: Attached scsi generic sg5 type 0
sd 50:0:0:1: [sdc] READ CAPACITY failed
sd 50:0:0:1: [sdc] Result: hostbyte=DID_NO_CONNECT driverbyte=DRIVER_OK
sd 50:0:0:1: [sdc] Sense not available.
sd 50:0:0:1: [sdc] Write Protect is off
sd 50:0:0:1: [sdc] Mode Sense: 00 00 00 00
sd 50:0:0:1: [sdc] Assuming drive cache: write through
sd 50:0:0:1: [sdc] READ CAPACITY failed
sd 50:0:0:1: [sdc] Result: hostbyte=DID_NO_CONNECT driverbyte=DRIVER_OK
sd 50:0:0:1: [sdc] Sense not available.
sd 50:0:0:1: [sdc] Assuming drive cache: write through
sd 50:0:0:1: [sdc] Attached SCSI removable disk
usb 2-3: new high speed USB device using ehci_hcd and address 35
usb 2-3: New USB device found, idVendor=0624, idProduct=0249
usb 2-3: New USB device strings: Mfr=1, Product=2, SerialNumber=3
usb 2-3: Product: USB Composite Device-1
usb 2-3: Manufacturer: Avocent
usb 2-3: SerialNumber: 20120430
usb 2-3: configuration #1 chosen from 1 choice
scsi51 : SCSI emulation for USB Mass Storage devices
usb-storage: device found at 35
usb-storage: waiting for device to settle before scanning
scsi52 : SCSI emulation for USB Mass Storage devices
usb-storage: device found at 35
usb-storage: waiting for device to settle before scanning
usb-storage: device scan complete
usb-storage: device scan complete
scsi 52:0:0:0: CD-ROM iDRAC Virtual CD 0323 PQ: 0 ANSI: 0
scsi 51:0:0:0: Direct-Access iDRAC LCDRIVE 0323 PQ: 0 ANSI: 0 CCS
scsi 52:0:0:1: Direct-Access iDRAC Virtual Floppy 0323 PQ: 0 ANSI: 0 CCS
sd 51:0:0:0: Attached scsi generic sg4 type 0
sd 51:0:0:0: [sdc] Attached SCSI removable disk
sr1: scsi3-mmc drive: 0x/0x cd/rw caddy
sr 52:0:0:0: Attached scsi CD-ROM sr1
sr 52:0:0:0: Attached scsi generic sg5 type 5
sd 52:0:0:1: Attached scsi generic sg6 type 0
sd 52:0:0:1: [sdd] Attached SCSI removable disk
usb 2-3: USB disconnect, address 35
usb 5-2: reset full speed USB device using uhci_hcd and address 82
usb 5-2: device descriptor read/64, error -71
usb 5-2: device descriptor read/64, error -71
usb 5-2: reset full speed USB device using uhci_hcd and address 82
usb 5-2: device descriptor read/64, error -71
usb 5-2: device descriptor read/64, error -71
usb 5-2: reset full speed USB device using uhci_hcd and address 82
usb 5-2: device not accepting address 82, error -71
usb 5-2: reset full speed USB device using uhci_hcd and address 82
usb 5-2: device not accepting address 82, error -71
usb 5-2: USB disconnect, address 82
usb 5-2: new full speed USB device using uhci_hcd and address 83
usb 5-2: device descriptor read/64, error -71
usb 5-2: device descriptor read/64, error -71
usb 5-2: new full speed USB device using uhci_hcd and address 84
usb 5-2: device descriptor read/64, error -71
usb 5-2: device descriptor read/64, error -71
usb 5-2: new full speed USB device using uhci_hcd and address 85
usb 5-2: device not accepting address 85, error -71
usb 5-2: new full speed USB device using uhci_hcd and address 86
usb 5-2: device not accepting address 86, error -71
hub 5-0:1.0: unable to enumerate USB device on port 2
usb 5-2: new full speed USB device using uhci_hcd and address 87
usb 5-2: New USB device found, idVendor=0624, idProduct=0248
usb 5-2: New USB device strings: Mfr=1, Product=2, SerialNumber=3
usb 5-2: Product: USB Composite Device-0
usb 5-2: Manufacturer: Avocent
usb 5-2: SerialNumber: 20120430
usb 5-2: configuration #1 chosen from 1 choice
input: Avocent USB Composite Device-0 as /devices/pci0000:00/0000:00:1d.0/usb5/5-2/5-2:1.0/input/input38
generic-usb 0003:0624:0248.0024: input,hidraw0: USB HID v1.00 Keyboard [Avocent USB Composite Device-0] on usb-0000:00:1d.0-2/input0
input: Avocent USB Composite Device-0 as /devices/pci0000:00/0000:00:1d.0/usb5/5-2/5-2:1.1/input/input39
generic-usb 0003:0624:0248.0025: input,hidraw1: USB HID v1.00 Mouse [Avocent USB Composite Device-0] on usb-0000:00:1d.0-2/input1
usb 2-3: new high speed USB device using ehci_hcd and address 36
usb 2-3: New USB device found, idVendor=0624, idProduct=0249
usb 2-3: New USB device strings: Mfr=1, Product=2, SerialNumber=3
usb 2-3: Product: USB Composite Device-1
usb 2-3: Manufacturer: Avocent
usb 2-3: SerialNumber: 20120430-1
usb 2-3: configuration #1 chosen from 1 choice
scsi53 : SCSI emulation for USB Mass Storage devices
usb-storage: device found at 36
usb-storage: waiting for device to settle before scanning
usb-storage: device scan complete
scsi 53:0:0:0: CD-ROM iDRAC Virtual CD 0323 PQ: 0 ANSI: 0
scsi 53:0:0:1: Direct-Access iDRAC Virtual Floppy 0323 PQ: 0 ANSI: 0 CCS
sr1: scsi3-mmc drive: 0x/0x cd/rw caddy
sr 53:0:0:0: Attached scsi CD-ROM sr1
sr 53:0:0:0: Attached scsi generic sg4 type 5
sd 53:0:0:1: Attached scsi generic sg5 type 0
sd 53:0:0:1: [sdc] Attached SCSI removable disk
usb 2-3: USB disconnect, address 36
usb 2-3: new high speed USB device using ehci_hcd and address 37
usb 2-3: New USB device found, idVendor=0624, idProduct=0249
usb 2-3: New USB device strings: Mfr=1, Product=2, SerialNumber=3
usb 2-3: Product: USB Composite Device-1
usb 2-3: Manufacturer: Avocent
usb 2-3: SerialNumber: 20120430
usb 2-3: configuration #1 chosen from 1 choice
scsi54 : SCSI emulation for USB Mass Storage devices
usb-storage: device found at 37
usb-storage: waiting for device to settle before scanning
scsi55 : SCSI emulation for USB Mass Storage devices
usb-storage: device found at 37
usb-storage: waiting for device to settle before scanning
usb-storage: device scan complete
usb-storage: device scan complete
scsi 54:0:0:0: Direct-Access iDRAC LCDRIVE 0323 PQ: 0 ANSI: 0 CCS
scsi 55:0:0:0: CD-ROM iDRAC Virtual CD 0323 PQ: 0 ANSI: 0
sd 54:0:0:0: Attached scsi generic sg4 type 0
scsi 55:0:0:1: Direct-Access iDRAC Virtual Floppy 0323 PQ: 0 ANSI: 0 CCS
sd 54:0:0:0: [sdc] Attached SCSI removable disk
sr1: scsi3-mmc drive: 0x/0x cd/rw caddy
sr 55:0:0:0: Attached scsi CD-ROM sr1
sr 55:0:0:0: Attached scsi generic sg5 type 5
sd 55:0:0:1: Attached scsi generic sg6 type 0
sd 55:0:0:1: [sdd] Attached SCSI removable disk
usb 2-3: USB disconnect, address 37
usb 5-2: reset full speed USB device using uhci_hcd and address 87
usb 5-2: device descriptor read/64, error -71
usb 5-2: device descriptor read/64, error -71
usb 5-2: reset full speed USB device using uhci_hcd and address 87
usb 5-2: device descriptor read/64, error -71
usb 5-2: device descriptor read/64, error -71
usb 5-2: reset full speed USB device using uhci_hcd and address 87
usb 5-2: device not accepting address 87, error -71
usb 5-2: reset full speed USB device using uhci_hcd and address 87
usb 5-2: device not accepting address 87, error -71
usb 5-2: USB disconnect, address 87
usb 5-2: new full speed USB device using uhci_hcd and address 88
usb 5-2: device descriptor read/64, error -71
usb 5-2: device descriptor read/64, error -71
usb 5-2: new full speed USB device using uhci_hcd and address 89
usb 5-2: device descriptor read/64, error -71
usb 5-2: device descriptor read/64, error -71
usb 5-2: new full speed USB device using uhci_hcd and address 90
usb 5-2: device not accepting address 90, error -71
usb 5-2: new full speed USB device using uhci_hcd and address 91
usb 5-2: device not accepting address 91, error -71
hub 5-0:1.0: unable to enumerate USB device on port 2
usb 5-2: new full speed USB device using uhci_hcd and address 92
usb 5-2: New USB device found, idVendor=0624, idProduct=0248
usb 5-2: New USB device strings: Mfr=1, Product=2, SerialNumber=3
usb 5-2: Product: USB Composite Device-0
usb 5-2: Manufacturer: Avocent
usb 5-2: SerialNumber: 20120430
usb 5-2: configuration #1 chosen from 1 choice
input: Avocent USB Composite Device-0 as /devices/pci0000:00/0000:00:1d.0/usb5/5-2/5-2:1.0/input/input40
generic-usb 0003:0624:0248.0026: input,hidraw0: USB HID v1.00 Keyboard [Avocent USB Composite Device-0] on usb-0000:00:1d.0-2/input0
input: Avocent USB Composite Device-0 as /devices/pci0000:00/0000:00:1d.0/usb5/5-2/5-2:1.1/input/input41
generic-usb 0003:0624:0248.0027: input,hidraw1: USB HID v1.00 Mouse [Avocent USB Composite Device-0] on usb-0000:00:1d.0-2/input1
usb 2-3: new high speed USB device using ehci_hcd and address 38
usb 2-3: New USB device found, idVendor=0624, idProduct=0249
usb 2-3: New USB device strings: Mfr=1, Product=2, SerialNumber=3
usb 2-3: Product: USB Composite Device-1
usb 2-3: Manufacturer: Avocent
usb 2-3: SerialNumber: 20120430-1
usb 2-3: configuration #1 chosen from 1 choice
scsi56 : SCSI emulation for USB Mass Storage devices
usb-storage: device found at 38
usb-storage: waiting for device to settle before scanning
usb 2-3: USB disconnect, address 38
usb 2-3: new high speed USB device using ehci_hcd and address 39
usb 2-3: New USB device found, idVendor=0624, idProduct=0249
usb 2-3: New USB device strings: Mfr=1, Product=2, SerialNumber=3
usb 2-3: Product: USB Composite Device-1
usb 2-3: Manufacturer: Avocent
usb 2-3: SerialNumber: 20120430
usb 2-3: configuration #1 chosen from 1 choice
scsi57 : SCSI emulation for USB Mass Storage devices
usb-storage: device found at 39
usb-storage: waiting for device to settle before scanning
scsi58 : SCSI emulation for USB Mass Storage devices
usb-storage: device found at 39
usb-storage: waiting for device to settle before scanning
usb-storage: device scan complete
scsi 57:0:0:0: Direct-Access iDRAC LCDRIVE 0323 PQ: 0 ANSI: 0 CCS
sd 57:0:0:0: Attached scsi generic sg4 type 0
usb-storage: device scan complete
sd 57:0:0:0: [sdc] Attached SCSI removable disk
scsi 58:0:0:0: CD-ROM iDRAC Virtual CD 0323 PQ: 0 ANSI: 0
scsi 58:0:0:1: Direct-Access iDRAC Virtual Floppy 0323 PQ: 0 ANSI: 0 CCS
sr1: scsi3-mmc drive: 0x/0x cd/rw caddy
sr 58:0:0:0: Attached scsi CD-ROM sr1
sr 58:0:0:0: Attached scsi generic sg5 type 5
sd 58:0:0:1: Attached scsi generic sg6 type 0
sd 58:0:0:1: [sdd] Attached SCSI removable disk
usb 2-3: USB disconnect, address 39
usb 5-2: reset full speed USB device using uhci_hcd and address 92
usb 5-2: device descriptor read/64, error -71
usb 5-2: device descriptor read/64, error -71
usb 5-2: reset full speed USB device using uhci_hcd and address 92
usb 5-2: device descriptor read/64, error -71
usb 5-2: device descriptor read/64, error -71
usb 5-2: reset full speed USB device using uhci_hcd and address 92
usb 5-2: device not accepting address 92, error -71
usb 5-2: reset full speed USB device using uhci_hcd and address 92
usb 5-2: device not accepting address 92, error -71
usb 5-2: USB disconnect, address 92
usb 5-2: new full speed USB device using uhci_hcd and address 93
usb 5-2: device descriptor read/64, error -71
usb 5-2: device descriptor read/64, error -71
usb 5-2: new full speed USB device using uhci_hcd and address 94
usb 5-2: device descriptor read/64, error -71
usb 5-2: device descriptor read/64, error -71
usb 5-2: new full speed USB device using uhci_hcd and address 95
usb 5-2: device not accepting address 95, error -71
usb 5-2: new full speed USB device using uhci_hcd and address 96
usb 5-2: device not accepting address 96, error -71
hub 5-0:1.0: unable to enumerate USB device on port 2
usb 5-2: new full speed USB device using uhci_hcd and address 97
usb 5-2: New USB device found, idVendor=0624, idProduct=0248
usb 5-2: New USB device strings: Mfr=1, Product=2, SerialNumber=3
usb 5-2: Product: USB Composite Device-0
usb 5-2: Manufacturer: Avocent
usb 5-2: SerialNumber: 20120430
usb 5-2: configuration #1 chosen from 1 choice
input: Avocent USB Composite Device-0 as /devices/pci0000:00/0000:00:1d.0/usb5/5-2/5-2:1.0/input/input42
generic-usb 0003:0624:0248.0028: input,hidraw0: USB HID v1.00 Keyboard [Avocent USB Composite Device-0] on usb-0000:00:1d.0-2/input0
input: Avocent USB Composite Device-0 as /devices/pci0000:00/0000:00:1d.0/usb5/5-2/5-2:1.1/input/input43
generic-usb 0003:0624:0248.0029: input,hidraw1: USB HID v1.00 Mouse [Avocent USB Composite Device-0] on usb-0000:00:1d.0-2/input1
usb 2-3: new high speed USB device using ehci_hcd and address 40
usb 2-3: New USB device found, idVendor=0624, idProduct=0249
usb 2-3: New USB device strings: Mfr=1, Product=2, SerialNumber=3
usb 2-3: Product: USB Composite Device-1
usb 2-3: Manufacturer: Avocent
usb 2-3: SerialNumber: 20120430-1
usb 2-3: configuration #1 chosen from 1 choice
scsi59 : SCSI emulation for USB Mass Storage devices
usb-storage: device found at 40
usb-storage: waiting for device to settle before scanning
usb 2-3: USB disconnect, address 40
usb 2-3: new high speed USB device using ehci_hcd and address 41
usb 2-3: New USB device found, idVendor=0624, idProduct=0249
usb 2-3: New USB device strings: Mfr=1, Product=2, SerialNumber=3
usb 2-3: Product: USB Composite Device-1
usb 2-3: Manufacturer: Avocent
usb 2-3: SerialNumber: 20120430
usb 2-3: configuration #1 chosen from 1 choice
scsi60 : SCSI emulation for USB Mass Storage devices
usb-storage: device found at 41
usb-storage: waiting for device to settle before scanning
scsi61 : SCSI emulation for USB Mass Storage devices
usb-storage: device found at 41
usb-storage: waiting for device to settle before scanning
usb-storage: device scan complete
usb-storage: device scan complete
scsi 61:0:0:0: CD-ROM iDRAC Virtual CD 0323 PQ: 0 ANSI: 0
scsi 60:0:0:0: Direct-Access iDRAC LCDRIVE 0323 PQ: 0 ANSI: 0 CCS
scsi 61:0:0:1: Direct-Access iDRAC Virtual Floppy 0323 PQ: 0 ANSI: 0 CCS
sd 60:0:0:0: Attached scsi generic sg4 type 0
sd 60:0:0:0: [sdc] Attached SCSI removable disk
sr1: scsi3-mmc drive: 0x/0x cd/rw caddy
sr 61:0:0:0: Attached scsi CD-ROM sr1
sr 61:0:0:0: Attached scsi generic sg5 type 5
sd 61:0:0:1: Attached scsi generic sg6 type 0
sd 61:0:0:1: [sdd] Attached SCSI removable disk
usb 2-3: USB disconnect, address 41
usb 5-2: reset full speed USB device using uhci_hcd and address 97
usb 5-2: device descriptor read/64, error -71
usb 5-2: device descriptor read/64, error -71
usb 5-2: reset full speed USB device using uhci_hcd and address 97
usb 5-2: device descriptor read/64, error -71
usb 5-2: device descriptor read/64, error -71
usb 5-2: reset full speed USB device using uhci_hcd and address 97
usb 5-2: device not accepting address 97, error -71
usb 5-2: reset full speed USB device using uhci_hcd and address 97
usb 5-2: device not accepting address 97, error -71
usb 5-2: USB disconnect, address 97
usb 5-2: new full speed USB device using uhci_hcd and address 98
usb 5-2: device descriptor read/64, error -71
usb 5-2: device descriptor read/64, error -71
usb 5-2: new full speed USB device using uhci_hcd and address 99
usb 5-2: device descriptor read/64, error -71
usb 5-2: device descriptor read/64, error -71
usb 5-2: new full speed USB device using uhci_hcd and address 100
usb 5-2: device not accepting address 100, error -71
usb 5-2: new full speed USB device using uhci_hcd and address 101
usb 5-2: device not accepting address 101, error -71
hub 5-0:1.0: unable to enumerate USB device on port 2
usb 5-2: new full speed USB device using uhci_hcd and address 102
usb 5-2: New USB device found, idVendor=0624, idProduct=0248
usb 5-2: New USB device strings: Mfr=1, Product=2, SerialNumber=3
usb 5-2: Product: USB Composite Device-0
usb 5-2: Manufacturer: Avocent
usb 5-2: SerialNumber: 20120430
usb 5-2: configuration #1 chosen from 1 choice
input: Avocent USB Composite Device-0 as /devices/pci0000:00/0000:00:1d.0/usb5/5-2/5-2:1.0/input/input44
generic-usb 0003:0624:0248.002A: input,hidraw0: USB HID v1.00 Keyboard [Avocent USB Composite Device-0] on usb-0000:00:1d.0-2/input0
input: Avocent USB Composite Device-0 as /devices/pci0000:00/0000:00:1d.0/usb5/5-2/5-2:1.1/input/input45
generic-usb 0003:0624:0248.002B: input,hidraw1: USB HID v1.00 Mouse [Avocent USB Composite Device-0] on usb-0000:00:1d.0-2/input1
usb 2-3: new high speed USB device using ehci_hcd and address 42
usb 2-3: New USB device found, idVendor=0624, idProduct=0249
usb 2-3: New USB device strings: Mfr=1, Product=2, SerialNumber=3
usb 2-3: Product: USB Composite Device-1
usb 2-3: Manufacturer: Avocent
usb 2-3: SerialNumber: 20120430-1
usb 2-3: configuration #1 chosen from 1 choice
scsi62 : SCSI emulation for USB Mass Storage devices
usb-storage: device found at 42
usb-storage: waiting for device to settle before scanning
usb 2-3: USB disconnect, address 42
usb 2-3: new high speed USB device using ehci_hcd and address 43
usb 2-3: New USB device found, idVendor=0624, idProduct=0249
usb 2-3: New USB device strings: Mfr=1, Product=2, SerialNumber=3
usb 2-3: Product: USB Composite Device-1
usb 2-3: Manufacturer: Avocent
usb 2-3: SerialNumber: 20120430
usb 2-3: configuration #1 chosen from 1 choice
scsi63 : SCSI emulation for USB Mass Storage devices
usb-storage: device found at 43
usb-storage: waiting for device to settle before scanning
scsi64 : SCSI emulation for USB Mass Storage devices
usb-storage: device found at 43
usb-storage: waiting for device to settle before scanning
usb-storage: device scan complete
usb-storage: device scan complete
scsi 64:0:0:0: CD-ROM iDRAC Virtual CD 0323 PQ: 0 ANSI: 0
scsi 63:0:0:0: Direct-Access iDRAC LCDRIVE 0323 PQ: 0 ANSI: 0 CCS
scsi 64:0:0:1: Direct-Access iDRAC Virtual Floppy 0323 PQ: 0 ANSI: 0 CCS
sd 63:0:0:0: Attached scsi generic sg4 type 0
sd 63:0:0:0: [sdc] Attached SCSI removable disk
sr1: scsi3-mmc drive: 0x/0x cd/rw caddy
sr 64:0:0:0: Attached scsi CD-ROM sr1
sr 64:0:0:0: Attached scsi generic sg5 type 5
sd 64:0:0:1: Attached scsi generic sg6 type 0
sd 64:0:0:1: [sdd] Attached SCSI removable disk
INFO: task sync:7381 blocked for more than 120 seconds.
"echo 0 > /proc/sys/kernel/hung_task_timeout_secs" disables this message.
sync D 0000000000000000 0 7381 7380 0x00000000
ffffffff814871f0 0000000000000086 0000000000000000 ffff8801f296be70
0000000000000000 0000000000000000 000000000000f9e0 ffff8801f296bfd8
00000000000157c0 00000000000157c0 ffff88032cb4e9f0 ffff88032cb4ece8
Call Trace:
[] ? bdi_sched_wait+0x0/0xe
[] ? bdi_sched_wait+0x9/0xe
[] ? __wait_on_bit+0x41/0x70
[] ? bdi_sched_wait+0x0/0xe
[] ? out_of_line_wait_on_bit+0x6b/0x77
[] ? wake_bit_function+0x0/0x23
[] ? sync_inodes_sb+0x73/0x12a
[] ? __sync_filesystem+0x4b/0x70
[] ? sync_filesystems+0x9a/0xe3
[] ? sys_sync+0x1c/0x2e
[] ? system_call_fastpath+0x16/0x1b
INFO: task sync:8501 blocked for more than 120 seconds.
"echo 0 > /proc/sys/kernel/hung_task_timeout_secs" disables this message.
sync D 0000000000000000 0 8501 8500 0x00000000
ffff88082e46b880 0000000000000086 0000000000000000 ffff8807e6dc9e70
0000000000000000 0000000000000000 000000000000f9e0 ffff8807e6dc9fd8
00000000000157c0 00000000000157c0 ffff8805a00b2a60 ffff8805a00b2d58
Call Trace:
[] ? bdi_sched_wait+0x0/0xe
[] ? bdi_sched_wait+0x9/0xe
[] ? __wait_on_bit+0x41/0x70
[] ? bdi_sched_wait+0x0/0xe
[] ? out_of_line_wait_on_bit+0x6b/0x77
[] ? wake_bit_function+0x0/0x23
[] ? sync_inodes_sb+0x73/0x12a
[] ? __sync_filesystem+0x4b/0x70
[] ? sync_filesystems+0x9a/0xe3
[] ? sys_sync+0x1c/0x2e
[] ? system_call_fastpath+0x16/0x1b
INFO: task sync:9883 blocked for more than 120 seconds.
"echo 0 > /proc/sys/kernel/hung_task_timeout_secs" disables this message.
sync D 0000000000000000 0 9883 9882 0x00000000
ffff88082e46b880 0000000000000082 0000000000000000 ffff88076fcbbe70
0000000000000000 0000000000000000 000000000000f9e0 ffff88076fcbbfd8
00000000000157c0 00000000000157c0 ffff8805a00b0000 ffff8805a00b02f8
Call Trace:
[] ? bdi_sched_wait+0x0/0xe
[] ? bdi_sched_wait+0x9/0xe
[] ? __wait_on_bit+0x41/0x70
[] ? bdi_sched_wait+0x0/0xe
[] ? out_of_line_wait_on_bit+0x6b/0x77
[] ? wake_bit_function+0x0/0x23
[] ? sync_inodes_sb+0x73/0x12a
[] ? __sync_filesystem+0x4b/0x70
[] ? sync_filesystems+0x9a/0xe3
[] ? sys_sync+0x1c/0x2e
[] ? system_call_fastpath+0x16/0x1b
INFO: task sync:10503 blocked for more than 120 seconds.
"echo 0 > /proc/sys/kernel/hung_task_timeout_secs" disables this message.
sync D 0000000000000000 0 10503 10502 0x00000000
ffff88082e46b880 0000000000000086 0000000000000000 ffff8805639c9e58
0000000000000000 0000000000000000 000000000000f9e0 ffff8805639c9fd8
00000000000157c0 00000000000157c0 ffff88082c87d4c0 ffff88082c87d7b8
Call Trace:
[] ? bdi_sched_wait+0x0/0xe
[] ? bdi_sched_wait+0x9/0xe
[] ? __wait_on_bit+0x41/0x70
[] ? bdi_sched_wait+0x0/0xe
[] ? out_of_line_wait_on_bit+0x6b/0x77
[] ? wake_bit_function+0x0/0x23
[] ? sync_inodes_sb+0x73/0x12a
[] ? __sync_filesystem+0x4b/0x70
[] ? sync_filesystems+0x9a/0xe3
[] ? sys_sync+0x1c/0x2e
[] ? system_call_fastpath+0x16/0x1b